Hardware Reference GuideHP MP9 Model 9000 Digital Signage Player
2 Hardware upgradesServiceability featuresThe computer includes features that make it easy to upgrade and service. No tools are needed for mostof the
Connecting the power cordWhen connecting the power supply, it is important to follow the steps below to ensure the power corddoes not pull free from t
Removing the computer access panelTo access internal components, you must remove the access panel:1. Remove/disengage any security devices that prohib
Replacing the computer access panelPlace the panel on the computer then slide it back (1) and tighten the thumbscrew (2) to secure thepanel in place.C
5. Orient the computer so that its right side is facing up and place the computer in the optional stand.NOTE: To stabilize the computer in a tower ori
Removing and replacing a hard driveNOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive sothat you can tran
8. Pull the release lever next to the rear of the hard drive outward (1). While pulling the release leverout, slide the drive back until it stops, the
11. Align the guide screws with the slots on the chassis drive cage, press the hard drive down into thebay, then slide it forward until it stops and l
Installing additional memoryThe computer comes with double data rate 3 synchronous dynamic random access memory (DDR3-SDRAM) small outline dual inline
Populating SODIMM socketsThere are two SODIMM sockets on the system board, with one socket per channel. The sockets arelabeled DIMM1 and DIMM3. The DI
© Copyright 2014 Hewlett-PackardDevelopment Company, L.P.Microsoft and Windows are U.S. registeredtrademarks of the Microsoft group ofcompanies.The in
Installing SODIMMsCAUTION: You must disconnect the power cord and wait approximately 30 seconds for the powerto drain before adding or removing memory
7. Disconnect the hard drive power cable (1) and data cable (2) from the system board.WARNING! To reduce risk of personal injury from hot surfaces, al
9. To remove a SODIMM, press outward on the two latches on each side of the SODIMM (1) thenpull the SODIMM out of the socket (2).10. Slide the new SOD
Replacing the batteryThe battery that comes with the computer provides power to the real-time clock. When replacing thebattery, use a battery equivale
6. Locate the battery and battery holder on the system board.7. Depending on the type of battery holder on the system board, complete the following in
b. Pull back on the clip (1) and slide the replacement battery down into the holder (2).Type 2a. Push the battery toward the outside of the chassis to
NOTE: After the battery has been replaced, use the following steps to complete this procedure.8. Replace the computer access panel.9. Plug in the comp
Installing a security lockThe security locks displayed below and on the following pages can be used to secure the computer.Cable lockPadlockInstalling
A Electrostatic dischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.
B Computer operating guidelines,routine care andshipping preparationComputer operating guidelines and routine careFollow these guidelines to properly
About This BookThis guide provides basic information for upgrading the HP Digital Signage Player.WARNING! Text set off in this manner indicates that f
Shipping preparationFollow these suggestions when preparing to ship the computer:1. Back up the hard drive files to an external storage device. Be sur
IndexAaccess panelremoval 6replacement 7Bbattery replacement 17Ccomputer operating guidelines 23Ddigital signage playerMP9000 1Eelectrostatic discharg
iv About This Book
Table of contents1 Product features ... 1
1 Product featuresStandard configuration featuresFeatures may vary depending on the model. For a complete listing of the hardware and softwareinstalle
Front panel components MP9 Digital Signage PlayerDrive configuration may vary by model. Some models have a bezel blank covering one or more drivebays.
Rear panel components MP9 Digital Signage Player1 DisplayPort Monitor Connectors 4 USB 3.0 Ports (blue)2VGA Monitor Connector 5 RJ-45 Network Connecto
Commentaires sur ces manuels