quick start guidehp surestore fc 1Gb/2Gb switch 16Bwww.hp.com
4 Quick Start Guide b. Turn on the power supply (flip the AC switch to “I”) when ready to supply power to the switch. The switch automatically runs PO
Installing the Switch 5The following items are required to install the switch in a rack:• FC 16B switch• Power cables• #2 Phillips and T25 Torx screwd
6 Quick Start Guide CAUTION For proper airflow, the SFP media side of the FC 16B faces the rear of the rack. This mounting allows air to enter from th
Installing the Switch 7– For a Compaq/Rittal rack, assemble each of the two brackets with (2) spacers, (2) M5 flat washers, and (1) M5 Torx head screw
8 Quick Start Guide Figure 4. Installing the Tinnerman Clips (HP Rack)– For a Compaq/Rittal rack, install (2) #10-32 square Tinnerman nuts for each of
Installing the Switch 95. Assemble the outer rails by completing the following steps:a. As an aid in assembly, two rubber washers have been included t
10 Quick Start Guide Figure 7. Assembling the Outer Rails (HP Rack)– For a Compaq/Rittal rack, install one #10-32 x 5/8 Phillips pan-head screw in the
Installing the Switch 11CAUTION Do not use any other screws other than the six that are provided. Use of any longer lengths can cause damage to intern
12 Quick Start Guide b. Turn on the power supply (flip the AC switch to “I”) when ready to supply power to the switch. The switch automatically runs P
132SETUPSystem ComponentsThe HP Surestore FC 1Gb/2Gb Switch 16B consists of the following components:• A 1U chassis, designed to be mounted in a 19-in
Notice© Hewlett-Packard Company, 2001. All rights reserved.Part number: A7340-96002Edition: E1201Hewlett-Packard Company makes no warranty of any kind
14 Quick Start Guide – One LED in the center of the power supply side to indicate the overall switch status.• Two universal input and redundant power
Setup 15The ports on the SFP media side of the FC 16B are color-coded in groups with four purple ports alternating with four unmarked ports to indicat
16 Quick Start Guide To turn the FC 16B on, connect one or both power supplies to a power source, then flip the AC power switch to the “I” position. T
Setup 17GBIC optic modules. LC to SC cables or adapters are required to connect the cables together.To connect an SC cable to the FC 16B, use the HP C
18 Quick Start Guide • Workstation that has a terminal emulator application (such as HyperTerminal)• Serial cable provided with the switch, for connec
Setup 19– In a UNIX environment, enter the following string at the prompt: tip /dev/ttyb -9600f. From the terminal emulator application, log on to the
20 Quick Start Guide Note The serial port is intended only for use during the initial setting of the IP address and for service purposes. Using the se
Setup 21a. Disable the switch by entering the following: switchDisableb. Enter the following: configurec. Enter the following at the Fabric parameters
22 Quick Start Guide c. Connect the cables to the SFPs as appropriate to the fabric topology. Position each cable so that the key (the ridge on one si
Setup 231. Verify that the RSHD service (on a UNIX machine) or the FTP service (on a Windows machine) is running on the host workstation.2. Login to t
iiiRevision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vUpdates . . . . . . . . . . . . . . .
24 Quick Start Guide system configuration file, and password is the password for the user ID specified. Note The password operand is only required if
Setup 25Configuring Supported DevicesHP Surestore Director FC-64 SwitchThe FC 16B switch can be used with the HP Surestore Director FC-64 switch. Spec
26 Quick Start Guide HP Surestore VA 7400The FC 16B also can support a 2Gb connection to an HP Surestore Virtual Array 7400. Set the port speed to 2Gb
273DIAGNOSTICSSwitch Status IndicatorsSystem activity and status can be determined through the activity of the LEDs on the switch. Note The LEDs may f
28 Quick Start Guide • One switch status LED in the center of the power supply side to indicate whether the switch is on and has successfully booted,
Diagnostics 29The following table describes the LEDs above each port on the right. These LEDs indicate the speed of the port.Fast-flashing green (on 1
30 Quick Start Guide The following table describes the LEDs below the serial port. These LEDs indicate the switch power.LEDs on the Power Supply SideF
Diagnostics 31The following table describes the LEDs on each power supply. These LEDs indicate the status of the related power supply.The following ta
32 Quick Start Guide Maintenance and Diagnostic TestsThe FC 16B does not require any regular physical maintenance, and is designed to minimize the cha
Diagnostics 33Note The transmit and receive speed of the links may be temporarily locked to a specific speed during diagnostic testing.Content Address
iv Quick Start Guide Next Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Setting QuickLoop
34 Quick Start Guide Error MessagesTo analyze error messages, access the error message log via a Telnet session using the errDump command. Note any me
354SPECIFICATIONSGeneralThe following table lists the general specifications for the HP Surestore FC 1Gb/2Gb Switch 16B.Specification DescriptionFabri
36 Quick Start Guide EnvironmentalThe following table lists the acceptable environmental ranges.Modes of operationFibre Channel Class 2 and Class 3Agg
Specifications 37DimensionsThe following table lists the dimensions of the FC 16B.Power SupplyThe following table lists the power supply specification
38 Quick Start Guide
39PRODUCT REGULATORY INFORMATIONFCC EMC Statement (USA)This equipment has been tested and found to comply with the limits for a Class A digital device
40 Quick Start Guide Germany Noise DeclarationSchalldruckpegel Lp = 46.1 dB(A)Am Arbeitsplatz (operator position)Normaler Betrieb (normal operation)Na
Product Regulatory Information 41Laser SafetyA. Certification and Classification InformationWhen equipped with native Fibre Channel adapters, this pro
42 Quick Start Guide Declaration of ConformityDECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Manufacturer's Name: Hewlett-P
vRevision HistoryUpdatesFor the most current information about the HP Surestore FC 1Gb/2Gb Switch 16B, visit the support Web site located at http://ww
Technical information in this document is subject to change without notice.© Copyright Hewlett-Packard Company 2001.All right reserved.Reproduction, a
vi Quick Start Guide For information about Fibre Channel standards, visit the Fibre Channel Association Web site, located at http://www.fibrechannel.c
11INSTALLING THE SWITCHProduct DescriptionThe HP Surestore FC 1Gb/2Gb Switch 16B is a 16-port Fibre Channel gigabit switch that supports link speeds u
2 Quick Start Guide • The ambient air temperature near the switch must not exceed 40 degrees Celsius. This is particularly important to verify if the
Installing the Switch 3• Four rubber mounting feet (used only for setting up the switch as a stand-alone unit)• Two rails and one bag of rail mounting
Commentaires sur ces manuels