HP Cooktop 10GBE Manuel d'utilisateur

10GbE Pass-Thru Module User Guide Part Number 573130-002 December 2010 (Second Edition)

Installing the pass-thru module 10 4. Close the handle (2). Complete installation is indicated by a green Health LED. If the Health LED is amber or

Installing the pass-thru module 11 Accessing the pass-thru module CLI locally 1. Using a null-modem mini-USB to DB-9 RS232 serial cable (not includ

Installing the pass-thru module 12 • The system/info command displays image version, board revision, or chip revisions. • The effect from any CLI

Replacing a pass-thru module 13 Replacing a pass-thru module Replacing an existing module CAUTION: Removing the pass-thru module from a powered

Updating the 10GbE pass-thru firmware 14 Updating the 10GbE pass-thru firmware Methods for updating the 10GbE Pass-Thru Module firmware CAUTION:

Updating the 10GbE pass-thru firmware 15 NOTE: If you are using a USB key to transfer the firmware file, see "Updating the firmware image us

Updating the 10GbE pass-thru firmware 16 12. Press the Enter key. The module console begins to print C characters until the Xmodem transfer begins.

Updating the 10GbE pass-thru firmware 17 Port 13 is ENABLED Port 14 is ENABLED Port 15 is ENABLED Port 16 is ENABLED Port 1 Installed CU SFP Port 1

Updating the 10GbE pass-thru firmware 18 Secondary DNS: 16.110.135.52 MAC Address: F4:CE:46:86:FA:5D Link Settings: Auto-Neg

Updating the 10GbE pass-thru firmware 19 NOTE: The pass-thru module boot code firmware image is usually named 10GPTHRU-w.x.y.z_FW.bin, where w.x.y

© Copyright 2009, 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warr

For more information 20 For more information Additional references Configure the 10GbE Pass-Thru Module after installation. Detailed information abo

Troubleshooting 21 Troubleshooting Health LED on the pass-thru module is not on Cause Action The pass-thru module is not seated properly. Be sure

Troubleshooting 22 Cannot access the pass-thru module serial console interface using an RS232 connection from a PC Terminal Emulation Program Cause

Troubleshooting 23 Cause Action More than one person is connected to the module console from Onboard Administrator. Use the Onboard Administrator C

Technical specifications 24 Technical specifications General specifications Category Specification Auto-negotiation standard: ANSI/IEEE 802.3 Nwa

Technical specifications 25 Port Link Ena Speed Neg Approved 12 Up/Downlink Dis/Ena 1Gb/10Gb On/Off Yes/No 13 Up/Downlink Dis/Ena 1Gb/1

Technical specifications 26 From Wire To Shell Braid Shell

Regulatory compliance notices 27 Regulatory compliance notices Class A equipment This equipment has been tested and found to comply with the limits

Regulatory compliance notices 28 product family and available (in English only) either within the product documentation or at the following HP websi

Regulatory compliance notices 29 WARNING: Use of controls or adjustments or performance of procedures other than those specified herein or in the

Contents 3 Contents Introduction ...

Electrostatic discharge 30 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Acronyms and abbreviations 31 Acronyms and abbreviations CLI Command Line Interface CPU central processing unit CSMA/CD Carrier Sense Multiple Acc

Acronyms and abbreviations 32 LAN local-area network MAC Media Access Control NAS network access server NIC network interface controller OS oper

Index 33 A accessing the pass-thru module CLI 10, 11 accessing the pass-thru module, troubleshooting 22 additional references 20 architecture

Index 34 port mapping 6 port names 24 R redundancy 6 regulatory compliance notices 27 replacing an existing pass-thru module 13 replacing

Contents 4 Cannot connect to the pass-thru module console interface remotely using Onboard Administrator ... 22 The download fail

Introduction 5 Introduction Features The 10GbE Pass-Thru Module is designed for easy installation and high performance in an environment where netwo

Introduction 6 Port mapping For detailed port mapping information, see the HP BladeSystem Enclosure Quick Setup Guide or the HP BladeSystem Enclosur

Component identification 7 Component identification 10GbE Pass-Thru Module front panel CAUTION: If you press the Reset button while the Health

Component identification 8 Item Description 4 Reset button 5 Mini-USB RS232 management serial port 6 Ports 1-16 SFP+ ports to support SFP and SF

Installing the pass-thru module 9 Installing the pass-thru module Manually configuring the pass-thru module Configure the pass-thru module manually