HP 240A Manuel d'utilisateur

DocuPrint 240A/340AHP-GL, HP-GL/2 Emulation Settings Guide

10 1 Using EmulationPaper MarginThe default output size is set to [A Size]. If the print data exceeds the effective coordinate area at all, it will be

1.4 Eject Function 111.4 Eject FunctionThis section explains the eject function. There are two types of eject functions as shown here.• The remaining

12 1 Using EmulationTo Eject All Jobs in the PrinterPrint all the jobs that the printer has received.Through this procedure, you can interrupt the rec

2.1 About Mode Menu 132 HP-GL Mode Settings2.1 About Mode MenuThis section explains the types of menus and the levels of the emulation mode menu.This

14 2 HP-GL Mode SettingsAbout Mode MenuThis HP-GL mode menu is used to set items specific to HP-GL and HP-GL/2 emulation.You can change the mode menu

2.2 HP-GL Mode Menu Settings 152.2 HP-GL Mode Menu SettingsThis section explains the items that can be set using HP-GL mode menu and the setting proce

16 2 HP-GL Mode SettingsDocument SizeSets the Client-Created document size.Candidate values are shown below.[Auto] (default)[Output Size]The size is t

2.2 HP-GL Mode Menu Settings 17Quantity SetupSets the method to specify the number of copies to print. Candidate values are shown below.[Protocol] (d

18 2 HP-GL Mode SettingsPrint ControlHP-GL ModeSwitches between graphics languages. This setting affects HP-GL commands (IW, OW, and UC commands).Can

2.2 HP-GL Mode Menu Settings 19Zoom ModeDetermines whether to use A-sizes (A0, A1, A2, A3, A4, and A5) or the effective coordinate area obtained by t

HP, HP-GL, and HP-GL/2 are registered trademarks of Hewlett-Packard Corporation.NetWare is a registered trademark of Novell, Inc., in the United State

20 2 HP-GL Mode SettingsImage EnhanceEnables or disables image enhancement.Image enhancement raises the resolution and smooths sharp edges.Candidate

2.2 HP-GL Mode Menu Settings 21DensitySets pen color density. The setting range is 0 to 100% in 5% increments. The default for pen No. 00 is 0%, and

22 2 HP-GL Mode SettingsSetting the HP-GL Mode MenuThis section uses a document size of [A4] set in the HP-GL mode to explain the mode menu setting pr

2.3 About the HP-GL Mode List 232.3 About the HP-GL Mode ListThis section explains the HP-GL mode list.Refer to• For information about reports and lis

24 2 HP-GL Mode Settings• HP-GL/2 Logical Printers/Stored Jobs ListYou can confirm the setting values that are in the NV memory.Print MethodOn the con

3.1 Hard Clip Area 253 Materials Related to HP-GL Mode3.1 Hard Clip AreaIn the HP-GL mode, the plottable area is determined (separately from the print

26 3 Materials Related to HP-GL Mode3.2 Printable AreaPrintable areas in the HP-GL mode are as follows:Note• Some output sizes may not be used dependi

3.2 Printable Area 27Output sizePaper length(1/7200 in.)Coordinate value(1/7200 in.)X-directionY-directionMargin Printable area Top right MarginWidth

28 3 Materials Related to HP-GL Mode3.3 Auto LayoutThis section explains auto layout.What Is Auto Layout?Auto layout is the function that judges the d

3.3 Auto Layout 29Area DetermineMethods for obtaining the effective coordinate area based on the HP-GL data are as follows:[Auto]An effective coordina

Preface 3PrefaceThank you for choosing this printer.This manual explains how to set up the printer to perform HP-GL/2 emulation. Be sure to read this

30 3 Materials Related to HP-GL ModeZoom ModeSelect the mode that determines the document size according to the obtained effective coordinate area. Al

3.3 Auto Layout 31Example:Assume that the following data is input when Zoom Mode = Output Size, Origin Position = Auto, Paper Margin = 10 mm, Area Det

32 3 Materials Related to HP-GL ModeWhen [Output Size] Is Set to [Auto]The size (A4, B5, or A5) of the paper set in the tray actually becomes the cand

3.3 Auto Layout 33Determining the Scaling FactorDuring execution of auto scaling, the scaling factor is determined by the document size and output siz

34 3 Materials Related to HP-GL ModeWhen [Document Size] Is Set to [Auto] and [Zoom Mode] Is Set to [Coordinate Area]The [Hard Clip] setting becomes i

3.3 Auto Layout 35Examples of Combinations of FunctionsThis section explains examples of print results obtained by combining the supported functions.D

36 3 Materials Related to HP-GL ModeDocument Size: Auto, Coord. Rotation: 0, Zoom Mode: Coordinate Area, Zoom: OnDocument Size: Auto, Coord. Rotation:

Index 37IndexAAuto Layout . . . . . . . . . . . . . . . . . . . . . . . . . . 28Eeject function . . . . . . . . . . . . . . . . . . . . . . . . .

Customer Response SheetDocuPrint 240A/340A HP-GL, HP-GL/2 Emulation Settings Guide (ME3216E2-1)To improve our publications, we would appreciate your f

DocuPrint 240A/340A HP-GL, HP-GL/2 Emulation Settings GuideHuman Interface Design DevelopmentDocument Products & Supply CompanyFuji Xerox Co., Ltd

4 Types of ManualsTypes of ManualsManuals Bundled With the Machine & Their ContentsManuals Bundled With Optional AccessoriesNote• Adobe® Acrobat®

List of Mode Menu (HP-GL)

Contents 5ContentsPreface... 3Types of Ma

6 Using This GuideUsing This GuidePrerequisite KnowledgeRead this guide in detail before using this printer. If you are not familiar with the machine

1.1 About Emulation 71 Using Emulation1.1 About EmulationThis chapter explains HP-GL, HP-GL/2 emulation of the print language available on this printe

8 1 Using EmulationSwitching Between Print LanguagesThis printer supports multi-emulation, allowing you to switch between print languages.There are th

1.2 Default Settings 91.2 Default SettingsYou can print in the following ways with the HP-GL and HP-GL/2 emulation modes set to the default settings.