HP B132L+ Manuel d'utilisateur Page 199
- Page / 256
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
185
SCSI Connections
Assigning SCSI Device IDs
NSE SCSI Device IDs
Before assigning a NSE SCSI device ID to your drive, you need to check
your NSE SCSI device IDs. To check what SCSI device IDs are available
and assign an ID to your device, follow these instructions which use Table
25:
1 Write in the NSE SCSI device ID of any internal drives in Table 25
2 Write in the type of external drives (SE SCSI, FW SCSI or Ultra SCSI) currently
connected to your system under the heading “External Device Drives” and each
drive’s SCSI device ID under the heading “Device ID.”
3 Add your new drive to the table if it is an external device. If it is an internal drive,
continue to Step 4.
NOTICE: The C1700A Magneto-Optical Autochanger uses three SCSI addresses,
and accounts for three of the seven devices allowed on the NSE SCSI bus.
4 Check to see which SCSI device IDs are not used. You can use ID numbers 0
through 6 if they are not already in use. If the default ID on your drive does not
conflict with any existing drive IDs, use that ID. If your default address conflicts
with an existing drive ID, you need to assign a new SCSI device ID to your drive.
See the drive installation documentation for information on changing the device
ID.
CAUTION: Do not use SCSI device ID 7 for any device. It is reserved for the built-in SCSI bus
controller
- Owner’s Guide 1
- Hewlett-Packard Co. 1997 2
- Contents 10
- Audience 16
- Release Document(s) 16
- Related Manuals 17
- Revision History 17
- Documentation Conventions 18
- System Overview 21
- Product Description 23
- System Power Switch 26
- Power LED 26
- System LEDs 26
- Audio Controls 27
- Removable Storage Devices 27
- Security Loop 29
- Audio Connectors 29
- Serial I/O Connectors 32
- SCSI Connectors 32
- TOC Button 33
- Power Cord Connector 33
- Monitors 34
- Keyboard 34
- Pointing Devices 34
- Operating System Overview 35
- LANIC ID 36
- Networking Overview 38
- Using Your CD-ROM Drive 41
- CD-ROM Drive 43
- CD-ROM Media 46
- Operating the CD-ROM Drive 47
- Reading the Busy Light 57
- Troubleshooting 59
- Tape Drive 61
- DDS Drive 63
- DDS-format tape drives 64
- 1/4 sec on 1/4 sec off 66
- 1/2 sec on, 1/2 sec off 66
- Data Cassettes 67
- Operating the DDS Tape Drive 70
- /usr/sbin/ioscan -d stape 71
- Using Device Files 72
- Archiving Data 73
- Writing to a Data Cassette 73
- Further Command Information 75
- Ordering Information 76
- Using the Floppy Diskette 79
- Operating the Floppy Drive 81
- Formatting a New Diskette 83
- For More Information 86
- Configuring the Floppy Driver 87
- Solving Problems 89
- Common Problems and Solutions 91
- LED Error Codes 98
- Dealing with a Boot Failure 101
- Device Verification 104
- Declaration of Conformity 1 107
- Declaration of Conformity 2 108
- Video connector 109
- Emissions Regulations 110
- VCCI Class 2 ITE 111
- Acoustics 113
- Safety Statement 115
- Visible LEDs 116
- Warnings and Cautions 117
- Changing Your Workstation’s 119
- Hardware Configuration 119
- Checking the SCSI IDs 121
- Preparing Your Workstation 123
- Installing Storage Devices 128
- Removing the Storage Tray 131
- Installing a Floppy Drive 137
- Replacing the Storage Tray 147
- Configuring a Hard Disk Drive 149
- Task started 150
- Creating the device file 150
- Modifying “/etc/checklist” 150
- Task completed 150
- Installing Additional memory 151
- Removing Memory Modules 152
- Installing Memory Modules 155
- Removing Cache Boards 158
- Cache Board Connectors 160
- Installing the Option Board 165
- Replacing the Battery 169
- RAM) Module 175
- Controller 177
- Changing Your Monitor Type 182
- SCSI Connections 185
- B160L/180L 186
- SCSI Bus Differences 187
- SCSI Restrictions 189
- Connectors and Terminators 191
- Determining SCSI Bus Length 194
- FWD SCSI Bus Length 195
- TotalUW 197
- (Total UW 197
- Assigning SCSI Device IDs 198
- NSE SCSI Device IDs 199
- FWD SCSI IDs 201
- Ultra, Wide-SE SCSI IDs 202
- Connecting to the SCSI Ports 204
- The Boot Console Interface 207
- Boot terminated 214
- Booting Your Workstation 215
- Searching for Bootable Media 217
- Resetting Your Workstation 218
- Displaying and Setting Paths 219
- path pri sescsi.6.0 221
- The Monitor Command 222
- MONITOR INFORMATION 223
- Setting the Monitor Type 224
- information 228
- Memory Information Sample 1 229
- Displaying System Information 238
- Displaying PIM Information 239
- Glossary 241
Produits connexes et manuels pour Serveurs HP B132L+
Serveurs HP 3PAR Manuel d'installation
(2 pages)
(2 pages)
Serveurs HP AXCRN3-2G Manuel d'utilisateur
(54 pages)
(54 pages)
Serveurs HP 339820-002 Manuel d'utilisateur
(78 pages)
(78 pages)
Serveurs HP DL280 Manuel d'utilisateur
(163 pages)
(163 pages)
Serveurs HP xw2x220c Guide de l'utilisateur
(104 pages)
(104 pages)
Serveurs HP A3661B Manuel d'utilisateur
(95 pages)
(95 pages)
Serveurs HP ML350 Manuel d'utilisateur
(44 pages)
(44 pages)
Serveurs HP 3PAR Guide de l'utilisateur
(144 pages)
(144 pages)
Serveurs HP Server tc2110 Guide de l'utilisateur
(118 pages)
(118 pages)
Serveurs HP D2220sb Manuel d'utilisateur
(51 pages)
(51 pages)
Serveurs HP GS1280 Manuel d'utilisateur
(59 pages)
(59 pages)
Serveurs HP AP836B Manuel d'utilisateur
(30 pages)
(30 pages)
Serveurs HP SL160Z Manuel d'utilisateur
(33 pages)
(33 pages)
Serveurs HP 64MB Manuel d'utilisateur
(39 pages)
(39 pages)
Serveurs HP SB600c Manuel d'utilisateur
(60 pages)
(60 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.509 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels