Hp Smart Array P600-Controller Manuel d'utilisateur Page 1

HP Smart Array P600 Controller for ProLiant Servers User Guide Part Number 384229-002 February 2007 (Second Edition)

Installing the controller hardware 10 2. Select an available 3.3-V, 64-bit full-length PCI or PCI-X slot. 3. If the controller is being hot-plugged

Installing the controller hardware 11 CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the s

Updating the firmware 12 Updating the firmware In this section Methods for updating the firmware...

Configuring an array 13 Configuring an array In this section Utilities available for configuring an array...

Setting the boot controller and controller order 14 Setting the boot controller and controller order In this section Setting a controller as the boo

Setting the boot controller and controller order 15 5. Exit from the utility. For more information about using RBSU, refer to the HP ROM-Based Setup

Installing device drivers and Management Agents 16 Installing device drivers and Management Agents In this section Installing device drivers...

Upgrading or replacing controller options 17 Upgrading or replacing controller options In this section Replacing a battery ...

Upgrading or replacing controller options 18 b. Lift the battery pack off the cache board (2). 4. Remove the secondary cache battery pack: a. Unh

Replacing, moving, or adding hard drives 19 Replacing, moving, or adding hard drives In this section Identifying the status of a hard drive...

© Copyright 2005, 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warra

Replacing, moving, or adding hard drives 20 Online/activity LED (green) Fault/UID LED (amber/blue) Interpretation Flashing regularly (1 Hz) Amber, f

Replacing, moving, or adding hard drives 21 Effects of a hard drive failure When a hard drive fails, all logical drives that are in the same array a

Replacing, moving, or adding hard drives 22 Replacing hard drives The most common reason for replacing a hard drive is that it has failed. However,

Replacing, moving, or adding hard drives 23 Automatic data recovery (rebuild) When you replace a hard drive in an array, the controller uses the fau

Replacing, moving, or adding hard drives 24 Observation Cause of rebuild termination None of the drives in the array have an illuminated amber

Replacing, moving, or adding hard drives 25 Upgrading hard drive capacity You can increase the storage capacity on a system even if there are no ava

Replacing, moving, or adding hard drives 26 4. Power up the system. If a 1724 POST message appears, drive positions were changed successfully and th

Diagnosing array problems 27 Diagnosing array problems In this section Controller board runtime LEDs...

Diagnosing array problems 28 LED ID Color LED name and interpretation 10 Amber CR509: Controller Failure LED. The controller hardware has detect

Diagnosing array problems 29 Item 1 (amber LED) Item 2 (green LED) Interpretation Slow blink (once every 16 seconds) This display pattern might occ

Contents 3 Contents Hardware features...

Electrostatic discharge 30 Electrostatic discharge In this section Preventing electrostatic discharge...

Regulatory compliance notices 31 Regulatory compliance notices In this section Federal Communications Commission notice ...

Regulatory compliance notices 32 to radio communications. However, there is no guarantee that interference will not occur in a particular installati

Regulatory compliance notices 33 This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C

Regulatory compliance notices 34 Japanese notice Korean notice Class A equipment Class B equipment Battery replacement notice This component us

Regulatory compliance notices 35 WARNING: There is a risk of explosion, fire, or personal injury if a battery pack is mishandled. To reduce this r

Acronyms and abbreviations 36 Acronyms and abbreviations ACU Array Configuration Utility ADG Advanced Data Guarding (also known as RAID 6) ADU Arr

Index 37 A ACU (Array Configuration Utility) 13 adding drives 26 ADU (Array Diagnostic Utility) 29 array controller installation overview 7 a

Index 38 L LEDs, cache module 28 LEDs, controller 27 LEDs, hard drive 19 logical drive capacity extension 26 logical drive, creating 13 M M

Contents 4 Cache module LEDs...

Hardware features 5 Hardware features In this section Board components ...

Hardware features 6 Temperature range Operating, 10° to 35°C (50° to 95°F); storage, -20° to 55°C (-4° to 131°F) Relative humidity (noncondensing)

Overview of the installation procedure 7 Overview of the installation procedure In this section Installing the controller in an unconfigured server.

Overview of the installation procedure 8 7. Disconnect peripheral devices. 8. Install the controller hardware ("Installing the controller hard

Installing the controller hardware 9 Installing the controller hardware In this section Before beginning the installation .......