HP G2 Manuel d'utilisateur télécharger pdf (Page 41)

Setup 41

NOTE: Identify the left (L) and right (R) rack rails by markings stamped

into the sheet metal.

3. Secure the back end of the rails to the rack.

IMPORTANT: Be sure that the scissor-type locking latches engage the

rack fully when the pins extend through the holes marked with the

template.

4. With one person on each side, lift the chassis to rail level and slide the

chassis on the mounting rails.

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 152 153

User Guide 1
Contents 3
Index 151 9
Component identification 11
Enclosure LEDs 12
Rear panel components 13
Component identification 15 15
Component identification 17 17
Controller components 18
Controller display 19
Controller LEDs 20
Component identification 21 21
SCSI IDs 22
Component identification 23 23
Component identification 25 25
Operations 27
Use the controller display 28
Types of messages 29
Using the interface 29
Rack planning resources 31
Optimum environment 32
Temperature requirements 33
Power requirements 34
Rack warnings 35
Shipping contents 36
Setup 37 37
Item Description 38
1 Rack rail (left) 38
2 Rack rail (right) 38
Setup 39 39
Setup 41 41
Setup 43 43
Installing hardware options 44
Installing servers 44
Choosing a configuration 44
Single-server configuration 45
SSP hardware configurations 45
Cabling the storage system 46
Power cords 47
Updating firmware 48
Firmware updates 49
Removing hard drive blanks 50
MSA500 G2 Controller option 53
Cache module upgrade option 55
2. Remove the controller 56
Configuration and utilities 59
HP Systems Insight Manager 60
Management Agents 60
Survey Utility 60
ROM functions and utilities 61
Enabling SSP 63
Array Configuration Utility 64
Array Diagnostic Utility 67
(CPQONLIN) 68
Cluster configuration 74
Troubleshooting 75
Diagnostic steps 76
Troubleshooting 77 77
Compromised fault tolerance 79
Troubleshooting 81 81
Time required for a rebuild 82
Troubleshooting 83 83
Display messages 85
Troubleshooting 87 87
Box numbering 88
Troubleshooting 89 89
05 System Name: <name> 90
06 Restarting System 91
08 Firmware Flash Failed 91
21 Scanning for SCSI Devices 92
22 Initializing SCSI Devices 92
Troubleshooting 93 93
40 Begin Redundancy Support 94
Troubleshooting 95 95
Troubleshooting 97 97
Troubleshooting 99 99
60 No Cache Module Found 101
65 Cache Hardware Enabled 103
Troubleshooting 105 105
Troubleshooting 107 107
Troubleshooting 109 109
89 Invalid Volume Addition 110
90 RIS Version Exceeded 111
Troubleshooting 113 113
Troubleshooting 115 115
121 No Volumes Detected 116
122 New Volumes Detected 117
124 Spares Cleared 118
Troubleshooting 119 119
303 ROM Cloning Started 121
304 ROM Cloning Done 122
305 ROM Cloning Failed 122
306 Firmware Flash Started 122
307 Firmware Flash Done 123
308 Firmware Flash Failed 123
309 EMU Flash Started 123
310 EMU Flash Done 124
311 EMU Flash Failed 124
Troubleshooting 125 125
Troubleshooting 127 127
Troubleshooting 129 129
Troubleshooting 131 131
FCC rating label 134
Class A equipment 134
Class B equipment 135
Modifications 136
Japanese notice 138
BSMI notice 138
Korean notice A&B 139
Battery replacement notice 139
Electrostatic discharge 141
Specifications 143
Power specifications 144
Technical support 145
Acronyms and abbreviations 147

Commentaires sur ces manuels

Pas de commentaire

HP G2 Manuel d'utilisateur Page 41

Commentaires sur ces manuels

Produits connexes et manuels pour Le serveur à l'état brut HP G2