Hp Smart Update Manager Manuel d'utilisateur Page 84
- Page / 130
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
DescriptionParameter
YES, NO
Enables you to override or downgrade an existing installation of
components in the selected bundle.
FORCEBUNDLE
Possible values:
YES, NO
Downgrade to an earlier version of firmware for multi-node devices such
as hard drives and array controllers. (Applies to firmware only.)
DOWNGRADE
Possible values:
YES, NO
Rewrite the same version of firmware only for multi-node devices such as
hard drives and array controllers. (Applies to firmware only.)
REWRITE
Possible values:
YES, NO
Enables you to reboot, if required.REBOOTALLOWED
Possible values:
YES, NO
Create a message to be displayed prior to rebooting.REBOOTMESSAGE
Possible values:
Any string (not exceeding 256 characters)
Delay before rebooting.REBOOTDELAY
Possible values
Time in seconds
Limit the list of components to be updated.COMPONENTSLIST
Possible values:
Component names with file extensions (.exe, .rpm, or .scexe)
Limit the list of bundle xml files to be filtered.BUNDLESLIST
Possible values:
Bundle file names
This is a filter switch and enables you to install newer versions of
components defined in a PSP, ISP, or bundle.
ALLOWUPDATEBUNDLE
This parameter enables these components to replace the older versions of
the same component that might have shipped with the bundles.
Possible values:
YES, NO
Defines the behavior when a remote node has an existing HP SUM session
in progress.
SKIPTARGET
Use this parameter to skip the host if an existing HP SUM session already
exists. A value of NO overrides the session in progress and reinitializes the
installation framework on the remote host.
NOTE: If an HP SUM session discovers a remote node is running HP
SUM locally, HP SUM ignores the SKIPTARGET command and skips the
remote node.
Possible values:
YES, NO
84 Using legacy scripts to deploy updates
- Version 6.2.0 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 8 Contents 8
- 1 Introduction 9
- Status icon descriptions 10
- HP SUM new terms 11
- Downloading HP SUM 12
- Deploying HP SUM 13
- Running HP SUM 14
- Deployment modes 15
- Deployment scenarios 15
- Launching HP SUM 17
- Logging out of the HP SUM GUI 18
- 3 Using the HP SUM GUI 19
- 20 Using the HP SUM GUI 20
- Adding a baseline 22
- Baseline reports 23
- Creating a custom baseline 23
- Deleting a baseline 24
- Using the Nodes screen 25
- Selecting multiple nodes 26
- Adding a node 26
- To add a node 27
- Editing a node 28
- Aborting a node update 29
- Node inventory 29
- Deploying a node 30
- Node reports 31
- Deleting a node 32
- Server overview 32
- Integrity node overview 32
- Using the Enclosures screen 33
- 34 Using the HP SUM GUI 34
- Editing an enclosure 35
- Aborting an enclosure update 35
- Enclosure inventory 36
- Deploying an enclosure 36
- Using the Servers screen 37
- 38 Using the HP SUM GUI 38
- Editing a server 39
- Aborting a server update 40
- Server inventory 40
- Deploying a server 40
- Server reports 41
- Using the Switches screen 42
- Using the Switches screen 43 43
- Editing a switch 44
- Aborting a switch update 44
- Switch inventory 44
- Deploying a switch 45
- Using the VM Hosts screen 46
- Using the VM Hosts screen 47 47
- Editing a VM host 48
- Aborting a VM host update 49
- VM hosts inventory 49
- Deploying a VM host 49
- VM host reports 50
- Using the iLO screen 51
- 52 Using the HP SUM GUI 52
- Editing an iLO 53
- Aborting an iLO update 53
- Deploying an iLO 54
- Deleting an iLO 55
- Adding an iPDU 55
- 56 Using the HP SUM GUI 56
- Editing an iPDU 57
- Aborting an iPDU update 58
- Deploying an iPDU 58
- To deploy a node 59
- Deleting an iPDU 60
- Adding a Virtual Connect 60
- Editing a Virtual Connect 62
- Virtual Connect inventory 63
- Deploying a Virtual Connect 63
- Virtual Connect reports 64
- Deleting a Virtual Connect 65
- Adding an iLO Federation 65
- 66 Using the HP SUM GUI 66
- Editing an iLO Federation 67
- Deleting an iLO Federation 68
- Command-line interface 69
- Command-line arguments 70
- Command-line examples 78
- Single-node servers: 80
- Multi-node servers: 80
- Input files 81
- Input file format and rules 82
- File encoding 83
- Error reporting 83
- Input file parameters 83
- Input files 93 93
- 5 Advanced topics 96
- GatherLogs 98
- 6 Troubleshooting 99
- Baseline troubleshooting 100
- Node troubleshooting 101
- VMware troubleshooting 102
- Reports troubleshooting 103
- HP SUM engine troubleshooting 103
- 104 Troubleshooting 104
- 7 Console Commands 105
- Activate 106
- Parameters 107
- Return codes 108
- FindAvailableNodes 110
- GenerateReports 111
- GetAttributes 112
- GetBaselines 113
- GetComponentLogs 114
- GetCurrentlyInstalledVersions 115
- GetEngineStatus 116
- GetNeededUpdates 117
- GetNodes 118
- Inventory 119
- SetAttributtes 120
- ShutdownEngine 121
- 8 Support and other resources 123
- Typographic conventions 124
- HP Insight Online 125
- 9 Documentation feedback 126
- Glossary 127
- 128 Index 128
- 130 Index 130
Produits connexes et manuels pour Logiciel Hp Smart Update Manager
(79 pages)
(81 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels