Hp 3000 Enterprise Virtual Array Manuel d'utilisateur Page 94
- Page / 161
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Figure 38 Re
moving a power supply
Installing a power supply
1. Lift up on the module latch (1, Figure 39) and slide the power s upply into the enclosure until it is
fully seated.
2. Connect the power cord to the p ower supply and engage the c ord lock.
Figur
e 39 Ins ta lling a power supply
V erify ing proper operation
After replacing the power supply or blower, check the following to verify that the component is operating
properly:
NOTE:
It may take up to 10 minutes for the component to display good status.
• Make sure the blower begins op erating immediately.
• The status indicator should be on.
94
Customer replaceable units
- HP StorageWorks 1
- Contents 3
- About this guide 11
- Rack stability 13
- HP technical support 13
- 1 Enterpr ise Virtu al Array 15
- Ease of management 16
- Data availability 16
- Performance 16
- Scalability 16
- Storage system components 17
- HP Command View E 18
- Controller software 18
- Hardware 19
- Fibre Channel loop switches 20
- HSV110 and HSV100 controllers 20
- P = Fibre (Host) Port 24
- CA = Fibre Channel Adapter 24
- Gathering information 25
- Host information 26
- Entering the WWN 27
- Entering the WWN checksum 27
- Installing opti 29
- 3 Enterpr ise Virtu al Array 31
- Setting Point in time 32
- Behavior 32
- Storage system s 35
- Adding disk driv 38
- Adding a disk drive 39
- Installing the disk drive 40
- Checking status indicators 40
- 1. Activity 41
- 2. Online 41
- 3. Fault 41
- Handling fiber o 42
- 4 Enterpr ise Virtu al Array 43
- I/O modules 44
- I/O module status indicators 45
- Fibre O ptic Fibr 47
- Copper Fibre Channel cables 47
- Fibre Channel disk drives 47
- Disk drive stat 48
- Disk drive status d isplays 48
- Power supplies and blowers 49
- Power supplies 50
- Drive enclosure EMU 51
- EMU functions 52
- EMU monitoring functions 53
- EMU displays 53
- EMU indicator di 54
- Audible alarm operations 55
- Enabling the audible alarm 56
- Muting or unmut 57
- Disabling the audible alarm 57
- Enclosure numb 58
- Error Condition Reporting 60
- Reporting group feature 63
- Reading the switch indicators 65
- Power-on self test (POST) 65
- HSV controllers 67
- High availability features 68
- Operator control panel 68
- Status indicators 69
- Navigation butt 70
- Alphanumeric display 70
- Displaying the OCP menu tree 70
- Displaying system information 71
- Shutting down the system 72
- Shutting the controller down 72
- Restarting the system 73
- Uninitializing the system 73
- Password options 73
- Changing a passw ord 73
- Clearing a passwor d 74
- Cache battery 75
- HSV controller cabling 75
- Rack configurations 75
- Power distribution 75
- Rack AC po 78
- Moving and stabilizing a rack 80
- 1. Hex nut 81
- 2. Leveler foot 81
- Customer self 83
- Component replacement videos 84
- Verifying component failure 84
- Procuring the spare part 84
- See Figure 31 85
- Figure 31 Disk drive label 85
- Replacing a disk drive 87
- Removing a disk 89
- Installing a disk drive 90
- V erify ing proper operation 90
- Adding a disk to a disk group 90
- Before you begin 91
- Removing a blower 92
- Installing a blower 92
- Removing a power supply 93
- Installing a power supply 94
- Returning the 95
- Customer replaceable units 96
- A Regulatory n otices and 97
- Laser device 98
- Laser safety warnings 99
- Class A equipment 99
- Class B equipment 99
- European union notice 100
- Notice for France 100
- WEEE Recycling Notices 100
- Greek notice 102
- Hungarian notice 102
- Portuguese notice 103
- Latvian notice 103
- Lithuanian notice 103
- Polish not 103
- Slovakian notice 104
- Slovenian notice 104
- Spanish not 104
- Swedish notice 104
- Harmonics conformance (Japan) 105
- Physical specifications 106
- Environmental s 107
- Power specifications 107
- Controller speci fications 109
- Power specificat 110
- Environmental specifications 110
- Rack specifications 111
- Nominal input voltage 113
- Specifications 113
- The power 113
- Condition r eport format 115
- Correcting errors 116
- Power supply conditions 118
- 0.2.en.02 119
- Blower conditions 120
- Temperature conditions 121
- 0.4.en.03 NON 123
- EMU conditions 124
- Transceiver conditions 128
- 0.F.en.04 CRI 129
- Backplane conditions 130
- I/O Module conditions 131
- Host conditions 133
- C Controller fault management 135
- Fault management displays 136
- Controller fault management 138
- Glossary 139
Produits connexes et manuels pour Stockage Hp 3000 Enterprise Virtual Array
Stockage Hp XP7 Storage Manuel d'utilisateur
(258 pages)
(258 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.289 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels