Hp 4000.6000.8000 Enterprise Virtual Arrays Manuel d'utilisateur Page 103
- Page / 169
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1
2
3
Figure 50 Power supply/blower status indicator
1. Status indicator
2. Power s upply/blower 1
3. Power supply/blower 2
Removing a blower
It is not necessary to remove the power supply to replace a failed blower.
WARNING!
The blower motor does not stop immediately when the blower is removed. Keep your fingers away from
the blower blades until the motor stops.
• While pushing in on the t wo wine-colored mounting tabs (1, Removing a blower), pull the blower
(2) away from the power supply.
Figure 51 Removing a blower
Installing a blower
CAUTION:
Pressing on the center section of the blower can damage the blades or the housing. Only press on
the outer edge of the blower when installing it.
1. Align the blower guide post (2, Installing a b lower) with the mounting hole next to the power
suppl
y connector (1).
2. Slide the blower onto the power supply (4) until the mounting tabs (3) snap into place.
4000/6000/8000 Enterprise Virtual Array user guide
103
- HP StorageWorks 1
- Contents 3
- About this guide 13
- Document conven 14
- Rack stability 15
- HP technical support 15
- 1 Enterpr ise Virtu al Array 17
- Ease of management 18
- Data availability 18
- Performance 18
- Scalability 18
- Storage system components 19
- HP Command View 20
- Controller software 20
- Hardware 21
- Fibre Channel loop switches 22
- HSV210 and HSV200 controllers 22
- P = Fibre (Host) Port 26
- CA = Fibre Channel Adapter 26
- Dir ect connect 28
- Procedures for g 29
- Entering the WWN 30
- Entering the WWN checksum 31
- 3 Enterpr ise Virtu al Array 33
- Setting Point in time 34
- Behavior 34
- Powering up the s 37
- Creating disk groups 40
- Adding a disk dri v e 41
- Checking status indicators 42
- Handling fiber optic cables 43
- 4 Enterpr ise Virtu al Array 45
- I/O modules 46
- I/O module status indicators 47
- Fibre Optic Fibr 49
- Copper Fibre Channel cables 49
- Fibre Channel disk drives 49
- Disk drive status indicators 50
- Disk drive status displays 50
- Power supplies and blowers 51
- Power supplies 52
- Drive enclosure EMU 53
- EMU functions 54
- EMU monitoring functions 55
- EMU displays 55
- EMU i ndicator di 56
- Audible alarm operations 57
- Enabling the audib le alarm 58
- Disabling the audible alarm 59
- Enclosure numb 60
- Error Condition Reporting 62
- Reporting group feature 65
- HSV cont 68
- High availability features 69
- Operator control panel 69
- Status indicators 70
- Navigation buttons 71
- Alphanumeric display 71
- Displaying the O CP menu tree 71
- Displayi 73
- Shutting down the system 74
- Shutting the controller down 74
- Restarting the system 75
- Uninitializing the system 75
- Password options 75
- Changing a pass 76
- Clearing a passwor d 76
- Cache battery 78
- HSV controller cabling 79
- Rack configurations 79
- Power distribut 80
- Rack AC power distribution 82
- Moving and stabilizing a rack 84
- 1. Hex nut 85
- 2. Leveler foot 85
- 5 Customer replaceabl e units 87
- Procuring the spare p art 88
- Replacing the cache battery 90
- Removing a battery 92
- Installing a bat tery 92
- Replacing a controller blower 93
- Removing 97
- Replacing a disk drive 98
- Removing a disk 99
- Installing a disk drive 100
- Adding a disk to the group 101
- Before you begin 101
- Verifying component failure 102
- Removing a blower 103
- Installing a blower 103
- Removing a power supply 104
- Installing a power supply 104
- V erifying proper operation 105
- Customer replaceable units 106
- A Regulatory n otices an d 107
- Laser device 108
- Laser safety warnings 109
- Class A equipment 109
- Class B equipment 109
- European union notice 110
- Notice for France 110
- WEEE Recycling Notices 110
- Greek notice 112
- Hungarian notice 112
- Latvian notice 113
- Lithuanian notice 113
- Polish not 113
- Portuguese notice 113
- Slovakian notice 114
- Slovenian notice 114
- Spanish not 114
- Swedish notice 114
- Harmonics conformance (Japan) 115
- Physical specifications 116
- Environmental s 117
- Power specifications 117
- Controller speci fications 119
- Power specificat 120
- Environmental specifications 120
- Rack specifications 121
- Condition report format 123
- Correcting errors 124
- Power supply conditions 126
- 0.2.en.02 127
- Blower conditions 128
- Temperature conditions 129
- 0.4.en.03 NON 131
- EMU conditions 132
- Transceiver conditions 136
- Backplane cond 139
- I/O M odule conditions 139
- CXO7951A 140
- Host conditio 141
- C Controller fault management 143
- Fault management displays 144
- Controller fault management 146
- Glossary 147
- XCS version,73 169
Produits connexes et manuels pour Stockage Hp 4000.6000.8000 Enterprise Virtual Arrays
Stockage Hp NetStorage 6000 Manuel d'utilisateur
(192 pages)
(192 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels