Hp P2000 G3 MSA Array Systems Manuel d'utilisateur Page 64
- Page / 86
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
64 Troubleshooting
Can you view a replication image?
Can you view remote systems?
Resolving voltage and temperature warnings
1. Check that all of the fans are working by making sure each power supply’s Voltage/Fan Fault/Service
Required LED is off or by using SMU to check for yellow yield icon hardware warnings. (In the
Configuration View panel, right-click the enclosure and select View > Overview.)
2. Make sure that all modules are fully seated in their slots and that their latches are locked.
3. Make sure that no slots are left open for more than two minutes.
If you need to replace a module, leave the old module in place until you have the replacement or use a
blank module to fill the slot. Leaving a slot open negatively affects the airflow and can cause the
enclosure to overheat.
4. Try replacing each power supply one at a time.
5. Replace the controller modules one at a time.
No Network error occurred during
in-progress replication.
• In SMU, review event logs for indicators of a specific fault
in a replication data path component.
• In SMU’s Configuration View panel, right-click the
secondary volume, and select View > Overview to
display the Replication Volume Overview table:
• Check for replication interruption (suspended) status
• Check for inconsistent status
•Check for offline status
• Replications that enter the suspended state must be
resumed manually.
No Communication link is down. See actions described in Can you view information about
remote links? on page 62.
Answer Possible reasons Actions
Answer Possible reasons Actions
Yes System functioning properly. No action required.
No Nonexistent replication image. • In SMU’s Configuration View panel, expand vdisks and
subordinate volumes to reveal the existence of a
replication image or images.
• If a replication image has not been successfully created,
use SMU to create one as described in the “Using Remote
Snap to replicate volumes” topic within the SMU guide.
No Communication link is down. See actions described in Can you view information about
remote links? on page 62.
Answer Possible reasons Actions
Yes System functioning properly. No action required.
No Non-existent replication set. See actions described in Can you replicate a volume? on
page 63.
No Communication link is down. See actions described in Can you view information about
remote links? on page 62.
- HP P2000 G3 iSCSI MSA System 1
- User Guide 1
- Acknowledgements 2
- Contents 3
- 4Contents 4
- 6Contents 6
- 8Figures 8
- 10 Tables 10
- About this guide 11
- Monospace, italic font 12
- Subscription service 13
- Rack stability 13
- HP technical support 13
- Customer self repair 13
- Product warranties 13
- HP websites 14
- Documentation feedback 14
- 1Overview 15
- 16 Overview 16
- 2Components 17
- Disk drive bay numbers 18
- Rear panel components 19
- D2700 6Gb drive enclosure 20
- MSA70 3Gb drive enclosure 20
- Transportable CompactFlash 21
- Super-capacitor pack 22
- 3Installing the enclosures 23
- 24 Installing the enclosures 24
- P2000 G3 Controller Enclosure 25
- Testing enclosure connections 33
- Powering on/powering off 33
- Power Cords 34
- DC model 35
- Power cycle 35
- 36 Installing the enclosures 36
- 4 Connecting hosts 37
- 1Gb iSCSI host ports 38
- 10GbE iSCSI host ports 38
- One server/one HBA/dual path 39
- Dual controller configuration 40
- Updating firmware 45
- 46 Connecting hosts 46
- Device description 47
- Obtaining IP values 47
- Connect USB cable to CLI 49
- IP-address 50
- 6 Basic operation 51
- 52 Basic operation 52
- 7Troubleshooting 53
- Diagnostic steps 54
- 56 Troubleshooting 56
- Transporting Cache 58
- 60 Troubleshooting 60
- Cabling for replication 61
- 62 Troubleshooting 62
- Can you replicate a volume? 63
- Can you view remote systems? 64
- Sensor locations 65
- Power supply sensors 65
- Cooling fan sensors 65
- Temperature sensors 65
- A LED descriptions 67
- Disk drive LEDs 68
- Rear panel LEDs 69
- LED Description Definition 70
- P2000 G3 1Gb iSCSI MSA 71
- Power supply LEDs 73
- Safety requirements 75
- Management host requirements 76
- Physical requirements 77
- Environmental requirements 78
- Electrical requirements 78
- Power cord requirements 79
- C Electrostatic discharge 81
- 82 Electrostatic discharge 82
- 84 Index 84
- 86 Index 86
Produits connexes et manuels pour Stockage Hp P2000 G3 MSA Array Systems
(93 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels