Hp Storage Mirroring V5 Software Manuel d'utilisateur Page 171
- Page / 212
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
19 - 25
Running DTStat from the command prompt
From a command prompt, use the DTStat command from the location where Storage Mirroring is installed.
Command DTSTAT
Description Starts the DTStats statistics logging utility from a command prompt.
Syntax
DTSTAT [-p][-i <interval>][-t <filename>] [-f <filename>][-s <filename>]
[-st <filename>][-IP <address>][-START <mm/dd/yyyy hh:mm>][-STOP <mm/dd/yyyy hh:mm>]
[-SERVER <ip_address> <port_number>]
Options -p—Do not print the output to the screen
-i interval—Refresh from shared memory every interval seconds
-t filename—Save the data from memory to the specified binary file filename
-f filename—Reads from a previously saved binary file, filename, that was generated using the -t
option instead of reading from memory
-s filename—Saves only the connection data from the data in memory to an ASCII,
comma-delimited file,
filename
-st filename—Saves only the target data from the data in memory to an ASCII, comma-delimited
file,
filename
-f filename1 -s filename2—Saves only the connection data from a previously saved binary file,
filename1, to an ASCII, comma-delimited file, filename2
-f filename1 -st filename2—Saves only the target data from a previously saved binary file,
filename1, to an ASCII, comma-delimited file, filename2
-IP address—Filters out the specified address in the IP address field and prints only those entries.
Specify more than one IP address by separating them by a comma.
-START mm/dd/yyyy hh:mm—Filters out any data prior to the specified date and time
-STOP mm/dd/yyyy hh:mm—Filters out any data after the specified date and time
SERVER ip_address port_number—Connects DTStat to the specified IP address using the
specified port number instead of to the local machine
Examples
DTStat -i 300
DTStat -p -i 300 -t AlphaStats.sts
DTStat -f AlphaStats.sts -s AlphaStats.csv -start 02/02/2007 09:25
DTStat -server 206.31.4.51 1106
Notes This command is not case-sensitive.
If no options are specified, DTStat will print the output to the screen at an interval of every one
second.
If the statistics are not changing, DTStat will discontinue writing until statistics begin updating
again.
- User’s Guide 1
- Table of Contents 3
- 1 X Introduction 8
- Storage Mirroring Overview 9
- Storage Mirroring operations 10
- Replication 11
- Restoration 13
- Server Recovery Option 14
- Full-Server Failover Option 15
- Sample configurations 17
- One-to-one, active/active 18
- Many-to-one 19
- One-to-many 20
- Description 21
- Applications 21
- Considerations 21
- Single server 22
- Virtual systems 23
- 3 X Installation 24
- 4 X Clients 34
- Creating groups 36
- Removing groups 36
- Moving servers 37
- Inserting servers 37
- Storage Mirroring workspaces 38
- Opening a workspace 39
- Failover Control Center 40
- Recovery Manager 41
- Full-Server Failover Manager 42
- 5 X Getting Started 44
- Protecting an entire server 46
- Recovering an entire server 48
- Configuring optional settings 51
- Finding a compatible target 55
- Starting failover 61
- Viewing the log 62
- Creating a replication set 68
- Establishing the connection 69
- Cluster configurations 73
- Configuring the hardware 80
- Gathering system information 81
- Managing Replication Sets 84
- Replication capabilities 85
- Modifying a replication set 87
- Deleting a replication set 88
- 14 X Managing Connections 90
- Monitoring connections 91
- Statistic Description 92
- Monitoring the message window 95
- Controlling mirroring 96
- Starting replication 99
- Configuring compression 100
- Verifying your data 102
- Scheduled verification 103
- Verification log 104
- Sample Verification Log 105
- Scheduled Snapshots 110
- Manual Snapshots 110
- Automatic Snapshots 110
- Understanding queuing 111
- Configuring queuing 112
- Blocking target paths 115
- Disconnecting a connection 115
- Controlling a target manually 116
- Setting bandwidth limitations 120
- 16 X Failover 123
- Configuration requirements 124
- WINS registration 125
- WINS replication 126
- Windows DNSCMD command 127
- Storage Mirroring DFO command 128
- Macintosh shares 131
- NFS shares 132
- Configuring failover 133
- Monitoring failover 137
- Updating shares manually 138
- Testing failover 138
- Failover manual intervention 139
- Restoration then failback 142
- Failback then restoration 145
- 19 X Monitoring Tools 147
- Log Files 148
- Viewing the log files 149
- Using LogViewer 150
- Log messages 151
- Windows Event Viewer 155
- DTStat statistics 172
- Windows Performance Monitor 176
- Configuring SNMP 178
- SNMP statistics 178
- SNMP traps 180
- 20 X Server Settings 183
- Licensing 185
- Move deleted files setting 193
- Database 194
- Script credentials 196
- E-mail notification 197
- 21 X Error Codes 199
- 22 X Security 204
- Storage Mirroring Groups 208
- Windows Active Directory 209
Produits connexes et manuels pour Stockage Hp Storage Mirroring V5 Software
(186 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.197 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels