HP 4100 Enterprise Virtual Array Manuel d'utilisateur Page 41
- Page / 180
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Table 15 30-10010-02 loop switch port status indicators
DescriptionPort bypass indicator
(Amber)
SFP status
indicator (Green)
Indicates that the port does not have an SFP installed and is bypassed
by the loop.
OffOff
Indicates that the port is operating normally. The port and device are
fully operational.
OffOn
Indicates the that port is in a bypassed state. The port is non-operational
due to loss of signal, poor signal integrity, or the Loop Initialization
Procedure (LIP).
NOTE: This condition is also normal when the SFP is present but not
attached to a Fibre Channel drive enclosure node, or when the SFP is
present and attached to only a cable assembly. Attaching the SFP to a
device and plugging it into the port should initiate the LIP by the attached
device.
OnOn
Indicates a Tx fault. The port is non-operational due to an SFP transmitter
fault, improperly-seated SFP, or another failed device.
OnOff
Problem isolation
Table 16 (page 41) lists several basic problems and their solutions.
Table 16 30-10010-02 loop switch basic troubleshooting
Recommended actionProblem
SFPs are installed in ports but no indicators
are lit.
1. Verify that the power cord is firmly seated in the switch and is
connected to the power outlet.
2. Check the power indicator to verify that the switch is on.
Re-seat the SFP. If the same condition occurs, the SFP is probably faulty
and should be replaced.
SFP is installed, but the Port Bypassed
indicator is lit.
This condition indicates that the switch is not receiving a valid Fibre
Channel signal or that the switch is receiving an LIP.
SFP is installed, but the SFP status indicator
and the Port Bypassed indicator are lit.
1. Ensure that the switch is powered on.
2. Contact your HP authorized service representative for further
assistance.
This condition indicates that the switch is receiving a valid Fibre Channel
signal, but there are no upper level protocols active.
SFP is installed and the SFP status indicator
is lit, but the devices are not communicating.
1. Verify that you are running the correct firmware on all storage system
hardware.
2. Check the Loop Operational indicator.
a. If the Loop Operational indicator is lit, the devices have completed
initialization.
b. If the Loop Operational indicator is off, the devices were not
initialized. Disconnect the devices from the switch. Reconnect the
devices one at a time. This allows you to isolate the device that
is responsible for the loop failure.
3. Contact your authorized service representative for further assistance.
HSV controllers
Two controllers (HSV210-A/B or HSV200-A/B) are contained in each rack. Each controller is
contained in a separate controller and provides the following features:
• High-performance microprocessor
• An Operator Control Panel (OCP)
HSV controllers 41
- HP EVA 4000/6000/8000 and EVA 1
- 4100/6100/8100 User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 8 Contents 8
- Contents 9 9
- 10 Contents 10
- Direct connect 13
- Fabric connect iSCSI 14
- Direct connect iSCSI 14
- Gathering information 15
- Entering the WWN 16
- Entering the WWN checksum 17
- 1. controllers 19
- 2. loop switches 19
- 3. disk enclosures 19
- Enclosure layout 20
- I/O modules 21
- I/O module status indicators 22
- Copper Fibre Channel cables 23
- Fibre Channel disk drives 23
- Disk drive status indicators 24
- Disk drive status displays 24
- Power supplies and blowers 25
- Drive enclosure EMU 26
- Controls and displays 27
- EMU functions 27
- EMU monitoring functions 28
- EMU displays 28
- EMU indicator displays 29
- Audible alarm operations 30
- Enabling the audible alarm 31
- Disabling the audible alarm 32
- Enclosure number feature 32
- Error Condition Reporting 34
- Reporting group feature 37
- Fibre Channel loop switches 38
- 30-10010-02 loop switch 39
- Power-on self test (POST) 40
- HSV controllers 41
- High availability features 43
- Operator control panel 43
- Status indicators 44
- Navigation buttons 45
- Alphanumeric display 45
- Displaying the OCP menu tree 45
- Displaying system information 47
- Shutting down the system 47
- Shutting the controller down 48
- Restarting the system 48
- Uninitializing the system 48
- Password options 49
- Changing a password 49
- Clearing a password 49
- Power supplies 50
- Cache battery 51
- HSV controller cabling 51
- Rack configurations 52
- Power distribution 52
- Racks 53 53
- 2. PDU 21. PDU 1 54
- 5. Mounting hardware 54
- Rack AC power distribution 55
- Moving and stabilizing a rack 56
- 2. Rear door1. Front door 57
- Racks 57 57
- 2. Leveler foot1. Hex nut 58
- Best practices 59
- Starting the storage system 65
- Creating disk groups 68
- Adding a disk drive 69
- Checking status indicators 70
- Handling fiber optic cables 71
- Overview 72
- Clustering 72
- Multipathing 72
- Adding hosts 73
- Scanning the bus 74
- Accessing IBM AIX utilities 75
- Driver failover mode 77
- Installing a Qlogic driver 77
- Upgrading Linux components 78
- Using the source RPM 79
- Channel FCA firmware 80
- Console LUN ID and OS unit ID 80
- Adding OpenVMS hosts 81
- Oracle Solaris 85 85
- Fabric setup and zoning 87
- 50001fe1002709e9,5 90
- Oracle Solaris 91 91
- SCSI Device Information: 92
- Configuring an ESX server 93
- Specifying DiskMaxLUN 94
- Verifying connectivity 94
- VMware 95 95
- 5 Customer replaceable units 96
- Replaceable parts 97
- Returning the defective part 100
- 6 Support and other resources 101
- Rack stability 102
- Customer self repair 103
- Regulatory notices 104
- Laser device 105
- European union notice 106
- Notice for France 106
- WEEE Recycling Notices 106
- Dutch notice 107
- Czechoslovakian notice 107
- Estonian notice 107
- Finnish notice 107
- French notice 108
- German notice 108
- Greek notice 108
- Hungarian notice 109
- Italian notice 109
- Latvian notice 109
- Lithuanian notice 109
- Polish notice 109
- Portuguese notice 110
- Slovakian notice 110
- Slovenian notice 110
- Spanish notice 110
- Germany noise declaration 111
- Japanese notice 111
- Taiwanese notice 111
- Japanese power cord notice 111
- Storage system specifications 112
- Power specifications 113
- Condition report format 117
- Correcting errors 117
- Drive conditions 118
- Correcting errors 119 119
- Power supply conditions 120
- Blower conditions 121
- Temperature conditions 123
- EMU conditions 125
- Correcting errors 127 127
- Transceiver conditions 128
- Correcting errors 129 129
- Resetting the EMU 130
- Backplane conditions 132
- I/O Module conditions 133
- Host conditions 134
- C Controller fault management 135
- Fault management displays 136
- Rack specifications 138
- Airflow and Recirculation 139
- Configuration Standards 139
- Power requirements 140
- UPS Selection 141
- Table 52 EVA 8x00 UPS loading 142
- Table 53 EVA 6x00 UPS loading 142
- Environmental specifications 143
- E Single Path Implementation 145
- Installation requirements 146
- Recommended mitigations 146
- Supported configurations 146
- HP-UX configuration 148
- Requirements 149
- HBA configuration 149
- Limitations 149
- Oracle Solaris configuration 151
- Tru64 UNIX configuration 152
- OpenVMS configuration 153
- Linux (32-bit) configuration 154
- Linux (64-bit) configuration 155
- IBM AIX configuration 156
- VMware configuration 157
- Failure scenarios 158
- Windows Server 159
- Oracle Solaris 159
- OpenVMS and Tru64 UNIX 160
- Glossary 163
- 164 Glossary 164
- 166 Glossary 166
- 168 Glossary 168
- 170 Glossary 170
- 172 Glossary 172
- 174 Glossary 174
- 176 Index 176
- 178 Index 178
- 180 Index 180
Produits connexes et manuels pour Non HP 4100 Enterprise Virtual Array
Non HP 6186C Manuel d'utilisateur
(58 pages)
(58 pages)
Non HP Compaq Notebook Manuel d'utilisateur
(42 pages)
(42 pages)
Non HP Sprinkler 1980 A Manuel d'utilisateur
(174 pages)
(174 pages)
Non HP MP7001 Manuel d'utilisateur
(1 pages)
Non HP 4938A Manuel d'utilisateur
(7 pages)
(7 pages)
Non HP c7000 Manuel d'utilisateur
(2 pages)
(2 pages)
Non HP R707 Manuel d'utilisateur
(1 pages)
(1 pages)
Non HP 002-01A Guide d'installation
(1 pages)
(1 pages)
Non HP 5400 Manuel d'utilisateur
(2 pages)
(2 pages)
Non HP iPAQ hx2000 Manuel d'utilisateur
(168 pages)
(168 pages)
Non HP xb31 Manuel de démarrage rapide
(10 pages)
(10 pages)
Non HP CA340 Manuel d'utilisateur
(4 pages)
(4 pages)
Non HP z553.fr Manuel d'utilisateur
(1 pages)
(1 pages)
Non HP M527 Garantie
(28 pages)
(28 pages)
Non HP Photosmart D7200 Manuel d'utilisateur
(16 pages)
(16 pages)
Non HP 345524-B21 Manuel d'utilisateur
(54 pages)
(54 pages)
Non HP 6269A Manuel d'utilisateur
(59 pages)
(59 pages)
Rockwell Automation 1492-IFMxxxx Sensor Interface Modules Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Ausrüstung Rockwell Automation 1492-IFMxxxx Sensor Interface Modules.
Wir stellen 2 PDF-Handbücher Rockwell Automation 1492-IFMxxxx Sensor Interface Modules zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Rockwell automation 1492-IFMxxxx Sensor Interface Modules Bedienungsanleitung (4 Seiten)
Marke: Rockwell-automation | Kategorie: Equipment | Größe: 0.49 MB |
Inhaltsverzeichnis
Rockwell automation 1492-IFMxxxx Sensor Interface Modules Bedienungsanleitung (6 Seiten)
Marke: Rockwell-automation | Kategorie: Equipment | Größe: 0.53 MB |
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Ausrüstung Rockwell Automation
| Modelle | Dokumententyp |
|---|---|
| 1606-XLSBATBR1 12V 7Ah Battery Module |
Bedienungsanleitung
Rockwell Automation 1606-XLSBATBR1 12V 7Ah Battery Module Benutzerhandbuch,
2 Seiten
|
| 871TM Inductive Proximity Sensor |
Bedienungsanleitung
Rockwell Automation 871TM Inductive Proximity Sensor User Manual,
2 Seiten
|
| 931S-C1A2D-OP Passive Isolator |
Bedienungsanleitung
Rockwell Automation 931S-C1A2D-OP Passive Isolator User Manual,
16 Seiten
|
| 1492-CM1771-LD0013F Field Wire Conversion Module |
Bedienungsanleitung
Rockwell Automation 1492-CM1771-LD0013F Field Wire Conversion Module User Manual,
6 Seiten
|
| 873C Ultrasonic Sensors |
Bedienungsanleitung
Rockwell Automation 873C Ultrasonic Sensors User Manual,
4 Seiten
|
| 1606-XLERED Power Supply Reference Manual |
Bedienungsanleitung
Rockwell Automation 1606-XLERED Power Supply Reference Manual User Manual,
20 Seiten
|
| 1606-XLSBATBR1 Power Supply Reference Manual |
Bedienungsanleitung
Rockwell Automation 1606-XLSBATBR1 Power Supply Reference Manual User Manual,
6 Seiten
|
| 1503F OEM Products - Isolation Switch Handle Modul |
Bedienungsanleitung
Rockwell Automation 1503F OEM Products - Isolation Switch Handle Module Instruction Sheet User Manual,
2 Seiten
|
| 1606-XLP15E Power Supply Reference Manual |
Bedienungsanleitung
Rockwell Automation 1606-XLP15E Power Supply Reference Manual User Manual,
24 Seiten
|
| 1606-XLP DC Power Supply (90 - 120W Units) |
Bedienungsanleitung
Rockwell Automation 1606-XLP DC Power Supply (90 - 120W Units) User Manual,
4 Seiten
|
| 1492-CM800-LD003 Field Wire Conv. Module for Modic |
Bedienungsanleitung
Rockwell Automation 1492-CM800-LD003 Field Wire Conv. Module for Modicon B805-016 or B853-016 to 1756-IA16 User Manual,
4 Seiten
|
| 1336_S_F_E_T D Frame Ferrite Core |
Bedienungsanleitung
Rockwell Automation 1336_S_F_E_T D Frame Ferrite Core User Manual,
1 Seiten
|
| Allen-Bradley Plot Software User Manual |
Bedienungsanleitung
Rockwell Automation Allen-Bradley Plot Software User Manual User Manual,
46 Seiten
|
| 1492-IFMxxxx Fusible Interface Module |
Bedienungsanleitung
Rockwell Automation 1492-IFMxxxx Fusible Interface Module Benutzerhandbuch,
4 Seiten
|
| 931H-A2A2N-DC Active Isolator |
Bedienungsanleitung
Rockwell Automation 931H-A2A2N-DC Active Isolator User Manual,
2 Seiten
|
| 931S-C4C5D-BC Active Converter |
Bedienungsanleitung
Rockwell Automation 931S-C4C5D-BC Active Converter User Manual,
40 Seiten
|
| 1329I Integrated AC Drive/Motor, Series A |
Bedienungsanleitung
Rockwell Automation 1329I Integrated AC Drive/Motor, Series A User Manual,
76 Seiten
|
| 1397 AC Tachometer Interface Card |
Bedienungsanleitung
Rockwell Automation 1397 AC Tachometer Interface Card User Manual,
8 Seiten
|
| 1494U- Disconnect Sw and Acc for Bul 502,502L,506, |
Bedienungsanleitung
Rockwell Automation 1494U- Disconnect Sw and Acc for Bul 502,502L,506,506X,512,512M,522E,522F User Manual,
2 Seiten
|
| 900-CPOEM1 Direct USB toTemperature / Process Cont |
Bedienungsanleitung
Rockwell Automation 900-CPOEM1 Direct USB toTemperature / Process Controller Configuration Cable User Manual,
1 Seiten
|
© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels