Hp ML100 Manuel d'utilisateur Page 48
- Page / 111
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
This symbol indicates the presence of a hot surface or hot component. If this surface
is contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the surface to
cool before touching.
20.41-27.22 kg
47.18-60 lb
This symbol indicates that the component exceeds the recommended weight for one
individual to handle safely.
WARNING: To reduce the risk of personal injury or damage to the equipment,
observe local occupational health and safety requirements and guidelines for
manual material handling.
These symbols, on power supplies or systems, indicate that the equipment is
supplied by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power
cords to completely disconnect power from the system.
Warnings and cautions
WARNING: Only authorized technicians trained by HP should attempt to repair this
equipment. All troubleshooting and repair procedures are detailed to allow only
subassembly/module-level repair. Because of the complexity of the individual boards and
subassemblies, no one should attempt to make repairs at the component level or to make
modifications to any printed wiring board. Improper repairs can create a safety hazard.
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:
• The leveling feet are extended to the floor.
• The full weight of the rack rests on the leveling feet.
• The stabilizing feet are attached to the rack if it is a single-rack installation.
• The racks are coupled together in multiple-rack installations.
• Only one component is extended at a time. A rack may become unstable if more than one
component is extended for any reason.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at
all times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed
against it. Pay particular attention to the plug, electrical outlet, and the point where the
cord extends from the server.
20.41-27.22 kg
47.18-60 lb
WARNING: To reduce the risk of personal injury or damage to the equipment:
• Observe local occupation health and safety requirements and guidelines for
manual handling.
• Obtain adequate assistance to lift and stabilize the chassis during installation or
removal.
Troubleshooting 48
- User Guide 1
- Intended audience 2
- Contents 3
- Operations 7
- Rack planning resources 9
- Optimum environment 9
- Setup 10 10
- Temperature requirements 11
- Power requirements 11
- Rack warnings 12
- Installing hardware options 12
- Registering the server 13
- Introduction 14
- Processor option 14
- DIMM identification 25
- Memory configurations 25
- Single-rank 24 GB 48 GB 26
- Dual-rank 24 GB 48 GB 26
- Quad-rank 24 GB 48 GB 26
- Installing 28
- Expansion board options 29
- ROM-Based Setup Utility 38
- Array Configuration Utility 39
- Management 40
- Keeping the system current 42
- Embedded SATA RAID feature 43
- USB diskette and CD-R 44
- OM drives 44
- Creating a diskette image 45
- Troubleshooting 47
- Warnings and cautions 48
- Symptom information 49
- Common problem resolution 50
- DIMM handling guidelines 51
- SAS and S TA 51
- Troubleshooting flowcharts 52
- General diagnosis flowchart 53
- Power-on problems flowchart 55
- POST problems flowchart 57
- Item See 58
- OS boot problems flowchart 59
- • Redundancy failure 61
- Hardware problems 62
- Power problems 63
- General hardware problems 64
- Unknown problem 65
- Third-party device problems 65
- Internal system problems 66
- DAT drive problems 67
- Diskette drive problems 68
- Fan problems 69
- Hard drive problems 69
- Data is inaccessible 70
- Memory problems 71
- PPM pro s 72
- Process p 72
- System e 73
- External device problems 73
- Audio problems 74
- Mouse and keyboard problems 75
- Software problems 79
- Operating system updates 80
- Linux operating systems 81
- Firmware maintenance 82
- Drivers 84
- Server in 84
- Microsoft® 85
- operating systems 85
- Battery 87
- Battery 88 88
- FCC rating label 89
- Class A equipment 89
- Class B equipment 89
- Modifications 90
- • EMC Directive 2004/108/EC 91
- Japanese notice 92
- Battery repl 94
- (Geräuschemission) 95
- Electrostatic discharge 96
- Technical support 97
- Technical support 98 98
- Technical support 99 99
- Technical support 100 100
- Reparo feito pelo cliente 101
- Technical support 102 102
- Technical support 103 103
- Technical support 104 104
- Acro abbreviations nyms and 105
- Index 108 108
- Index 109 109
- Index 110 110
- Index 111 111
Produits connexes et manuels pour Ordinateurs Hp ML100
Ordinateurs Hp Compaq Manuel d'utilisateur
(22 pages)
(22 pages)
Ordinateurs Hp PAVILION DV3 Manuel d'utilisateur
(114 pages)
(114 pages)
Ordinateurs Hp BL460C G6 Manuel d'utilisateur
(107 pages)
(107 pages)
Ordinateurs Hp DL185 Manuel d'utilisateur
(103 pages)
(103 pages)
Ordinateurs Hp LC 2000 Manuel d'utilisateur
(194 pages)
(194 pages)
Ordinateurs Hp XW6400X Manuel d'utilisateur
(90 pages)
(90 pages)
Ordinateurs Hp BL2X220C Manuel d'utilisateur
(82 pages)
(82 pages)
(102 pages)
Ordinateurs Hp BA322 90087 Manuel d'utilisateur
(346 pages)
(346 pages)
Ordinateurs Hp XW6200 Manuel d'utilisateur
(78 pages)
(78 pages)
Ordinateurs Hp LH 3r Manuel d'utilisateur
(23 pages)
(23 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.371 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels