HP 2524 Manuel d'utilisateur

Revision 1.3 July 2001

[no] page Toggles the paging mode for display commands so that the “—more –“ will appear or not appear. repeat Repeatedly executes the previous comman

copy <startup-config|running-config|crash-log|event-log|crash-rec|Command> tftp <ip-addr> <remote-file> This command writes the swit

clear intrusion-log To clear the intrusion log. clear statistics [ethernet] <port-list> To reset counters displayed by the console. If a new co

setmib <object-name> <type> <value> [<object-name> <type> <value> …] This command sets the MIB object defined by o

link-test <mac-addr> [vlan <vlan-id>] [repetitions <1..999>] [timeout <1..256>] Tests the connection to a MAC station on the L

---------------2.3 System Configuration 2.3.1 System commands - EXEC level show console Displays the console parameters. Output Format: Switch Confi

show mac-address <port-list> Displays the MAC addresses that the switch has learned from the network devices attached to the specified switch po

----------------------------------------------------------- show modules Displays the modules that are present on the switch. Output Format: Status a

2.3.2 System Configuration commands mac-age-time <1..100000> Sets the number of seconds a MAC address stays in the switch address table before b

time [mm/dd/yy] [hh:mm:ss] [timezone <value>] [daylight-time-rule <value>] [begin-date <mm/dd> end-date <mm/dd>] This command

[no] telnet-server Enables remote telnet access to the switch. [no] web-management Enables the web browser to interact with the web agent on the switc

2.5 TACACS 2.5.1 TACACS commands - EXEC level show tacacs Displays TACACS configuration. 2.5.2 TACACS commands - Configuration level [no] tacacs-se

2.7 IP Stacking 2.7.1 IP Stacking commands - EXEC level show stack [candidates | all] Displays status information for the stacking feature. ‘show s

[no] stack auto-join Causes the switch to advertise, via the discovery protocol, that it wants to automatically join any stack operating on the local

2.8 Port Settings 2.8.1 Port commands - EXEC level show interfaces config Displays the basic configuration of the switch ports. Output Format: Switc

show statistics <port-number> Displays the network traffic statistics for the specified port. Output Format: Status and Counters - Port Counters

--------------- ---------- ------ ------- --------- -------- show interfaces Displays the status and current configuration of all the switch por

1 2 3 4 5 6 7 8 --------[no] flow-control Enables or disables flow control on the port. Note: Full-dup

1 2 34 5 6 7 8 ------------------ -------- ----- -------- show lacp Displays LACP status information. Output Fo

1 2 3 4 5 6 7  [type <trunk | fec | lacp>] - Determines the method by which the switch distributes

Contents 1. INTRODUCTION ...

1 2 3 4 5 6 7 8 9 10 11 --------------------------- -------- ----- -------- show s

spanning-tree [forward-delay <seconds>] [hello-time <seconds>] [maximum-age <seconds>] [priority <0..65535>] spanning-tree <

------------------------------ 2.11 IP 2.11.1 IP commands - EXEC level show ip Displays the IP configuration on the switch. Output Format There are

----------------------------------------- ------------------------ -------- ---- ----------- ------------- show ip authorized-managers Displays

show timp Displays active Timep configuration. Output Format Timep Configuration Time Sync Mode: Timep TimeP Mode [Disabled] : Manual Server Address

2.11.2 IP commands - Configuration level [no] ip authorized-managers <ip-addr> [mask <ip-mask>] [operator | manager] Sets the IP addresse

[no] sntp < server <ip-addr> [version]> [poll-interval <30-720>] Configures SNTP on the switch. ip default-gateway <ip-addr> A

2.11.3 IP commands - VLAN Interface level [no] ip address <dhcp-bootp | <<ip-addr>/<1..32> | <ip-addr> <ip-mask>] [seco

--------------------- ----------------------------------- 2.12 SNMP 2.12.1 SNMP commands - EXEC level show snmp-server Displays the SNMP communitie

2.12.2 SNMP commands – Configuration Level [no] snmp-server community <community-name> [manager | operator] [restricted | unrestricted] Used to

2.16 PORT MONITORING...

1 2 3 4 5 6 7 8 ------------------------ ------------ ------------ 2.13 VLAN Configuration 2.13.1 VLAN co

primary-vlan <vlan-id> Sets the primary VLAN used for network management. [no] vlan <vlan-id> Creates a new VLAN or changes the system con

---- auto <port-list> Causes each port identified in the port-list to learn their VLAN membership using the Group VLAN Registration Protocol (G

----------------------------- ------- -------------------- ----------- -------- -------------------- ----------- -------- 2.15 IGMP 2.15.1 I

2.15.2 IGMP Configuration commands – Vlan Interface level [no] ip igmp Enables the IP Multicast (IGMP) feature for IGMP communication between Multica

2.16 Port Monitoring 2.16.1 Port Monitoring commands - EXEC level show mirror-port Displays the configuration of the monitoring port. Output Format:

2.16.3 Port Monitoring commands - VLAN Interface level [no] monitor Used to enable/disable monitoring of the VLAN. 2.16.4 Port Monitoring commands -

--------------------------------------- show port-security [ethernet] <port-list> Displays the port security configuration for an individual po

defined by the "address-limit" parameter are learned or entered for the port. These addresses are static; they are not aged out.  addr-lim

3. Console Menu HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -============================ Main Menu 1.

1. Introduction This document provides a summary of the commands supported on the HP ProCurve 2524, 2512, and 4108gl switches. It is divided into sec

3.1.1 General System Information HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -=========================

------------------------------------------------------------ --------------- ---------- ------ ------- --------- -------- 3.1.3 Module Informa

-------------------------- ------------- ------------- 3.1.5 Port Counters HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONS

---------------3.1.6 Address Table HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -=======================

--------------------------- -------- ----- ------------ 3.1.8 Spanning Tree Information HP ProCurve Switch xxxxx 01-Apr-2000 ==================

3.2 Configuration Menu HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -============================ Switch

--------------------- --------- ---------- 3.2.1 System Information HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - M

------- ---- 3.2.3 Network Monitoring Port HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -=============

--------------------------- 3.2.5 IP Configuration HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -======

-------------------- --------------------------- 3.2.6 SNMP Communities HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE

There are three "special" port designations in the switch. You may specify the monitoring port by using "mp"; you may specify a tr

3.2.8 VLAN Menu HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -============================ Switch Config

--------------3.2.8.2 VLAN Names HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -=========================

---- 3.3 Password Menu HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -============================ Set P

3.5 Download Screen HP ProCurve Switch xxxxx 01-Apr-2000 ==========================- CONSOLE - MANAGER MODE -============================ Download

Index A aaa authentication console ...16 aaa authentication telnet...16 arp...

show management...12 show mirror-port ...41 show modules...

If an operator password has been set (see password in the global configuration section), then the system would have displayed the following prompt bef

If you had already typed in trap- on line (1) and then pressed the tab character, the system would complete the keyword trap-send-authentication, for

2. Command Summary 2.1 User EXEC Commands enable Enters the manager EXEC level. If a manager password is set, the system will first prompt for the p