HP Moonshot Switch User and Maintenance Guide Abstract This document is for the person who installs, administers, services, and troubleshoots switc
Component and LED identification 10 Moonshot-180G Switch Module Switch module button, sensor, and LEDs Item Description Status 1 Switch module p
Component and LED identification 11 iLO CM management port The iLO CM management port provides communication with the switch service port interface
Operations 12 Operations Extend the chassis from the rack 1. Pull down the quick release levers on each side of the chassis. 2. Extend the chassis
Operations 13 Remove the access panel IMPORTANT: After performing a procedure inside the chassis, always install the access panel on the cha
Operations 14 NOTE: Turn the access panel over to locate the hood labels. These labels provide information on installing various options, flexibl
Operations 15 Remove the switch module blank Remove the component as indicated.
Setup 16 Setup Installation information and guidelines Before installing the module, review the following: • Always install the switch module and t
Setup 17 Uplink module bays The uplink module can be installed in the uplink module bays located in the rear of the chassis. Installing the uplink
Setup 18 2. Prepare the uplink module for installation. 3. Install the uplink module. 4. Do one of the following: o If the switch module is alr
Setup 19 3. Locate the switch module slot and remove the blank. 4. Prepare the switch module for installation.
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warrantie
Setup 20 5. Align and install the switch module into the chassis. 6. Do one of the following: o If the uplink module is already installed, verify
Configuration 21 Configuration Configuring the switch To configure the switch, see the Switch Administrator's Guide and the Switch CLI Command
Configuration 22 Network mapping Production network mapping The first network interface discovered by the operating system routes traffic through s
Configuration 23 Management network mapping All traffic from the service port management interface is routed through the iLO CM management port (on
Configuration 24 Item Port Interface 1 X1 1/1/1 2 X2 1/1/2 3 X3 1/1/3 4 X4 1/1/4 5 X5 1/1/5 6 X6 1/1/6 Interfaces 1/1/1–1/1/6 are the upli
Configuration 25 Moonshot-45G downlink interfaces Interfaces 1/0/1–1/0/45 are the downlinks to the cartridge nodes. Each SoC is identified as a car
Configuration 26 Moonshot-180G downlink interfaces Interfaces 1/0/1–1/0/180 are the downlinks to the cartridge nodes. Each SoC is identified as a c
Configuration 27 Command Line Interface Connect to the switch console To manage the switch, use one of the following ports to connect to the switch
Configuration 28 o No flow control 3. Start the terminal. The switch login prompt appears. 4. Enter: admin No password is set by default. Obtaini
Configuration 29 o show firmware revisions o show switch power o show switch temperature To set switch power or switch UID LED: o set switch powe
Contents 3 Contents Component and LED identification ...
Configuration 30 Firmware Update the switch firmware Switch firmware can be updated using the following CLIs: • The iLO CM firmware CLI • The swit
Configuration 31 update cpld The CPLD update reloads the switch and completes when the switch returns to an operational state. If no CPLD update is
Troubleshooting 32 Troubleshooting Troubleshooting resources The HP Moonshot System Troubleshooting Guide provides procedures for resolving common p
Illustrated parts catalog 33 Illustrated parts catalog Customer self repair HP products are designed with many Customer Self Repair (CSR) parts to m
Illustrated parts catalog 34 Switch customer self repair components Item Description Spare part number Customer self repair (on page 33) 1 HP M
Removal and replacement procedures 35 Removal and replacement procedures Removing the switch module CAUTION: Be sure to save the running-configu
Removal and replacement procedures 36 CAUTION: For proper cooling, be sure every switch module bay and uplink module bay has either a blank or a mo
Regulatory information 37 Regulatory information Safety and regulatory compliance For safety, environmental, and regulatory information, see Safety
Electrostatic discharge 38 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo
Electrostatic discharge 39 Specifications Chassis environmental specifications Specification Value Temperature range* — Operating 10°C to 35°C (50
Contents 4 Troubleshooting resources ...
Support and other resources 40 Support and other resources Before you contact HP Be sure to have the following information available before you call
Acronyms and abbreviations 41 Acronyms and abbreviations CM chassis management CMU HP Insight Cluster Management Utility CPLD complex programmable
Acronyms and abbreviations 42 SFP+ enhanced small form-factor pluggable SFTP Secure File Transfer Protocol SoC system on chip SR short range SSH
Documentation feedback 43 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentat
Index 44 A access panel 13 activity LED 5 administration 21 authorized reseller 40 B before you contact HP 40 blank, removal 14, 15 butt
Index 45 series number 37 setup 16 spare part numbers 33 static electricity 38 support and other resources 40 switch firmware, updating
Component and LED identification 5 Component and LED identification Chassis front panel LEDs and buttons Item Description LED Status 1 Chassi
Component and LED identification 6 Moonshot-6SFP Uplink Module Uplink module components Item Component Description 1 Serial console port For
Component and LED identification 7 Item Description Status 1 Uplink module UID LED/button Solid blue = Switch module ID is selected. Flashing blu
Component and LED identification 8 Uplink module buttons and LEDs Item Description Status 1 Uplink module UID LED/button Solid blue = Switch mod
Component and LED identification 9 Moonshot-45G Switch Module Switch module button, sensor, and LEDs Item Description Status 1 Switch module pow
Commentaires sur ces manuels