HP Elite 7100 Microtower PC Manuel d'utilisateur Page 34
- Page / 44
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Battery Replacement
The battery that comes with the computer provides power to the real-time clock. When replacing the
battery, use a battery equivalent to the battery originally installed in the computer. The computer comes
with a 3-volt lithium coin cell battery.
WARNING! The computer contains an internal lithium manganese dioxide battery. There is a risk of
fire and burns if the battery is not handled properly. To reduce the risk of personal injury:
Do not attempt to recharge the battery.
Do not expose to temperatures higher than 60°C (140ºF).
Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
Replace the battery only with the HP spare designated for this product.
CAUTION: Before replacing the battery, it is important to back up the computer CMOS settings. When
the battery is removed or replaced, the CMOS settings will be cleared. Refer to the Maintenance and
Service Guide for information on backing up the CMOS settings.
Static electricity can damage the electronic components of the computer or optional equipment. Before
beginning these procedures, ensure that you are discharged of static electricity by briefly touching a
grounded metal object.
NOTE: The lifetime of the lithium battery can be extended by plugging the computer into a live AC wall
socket. The lithium battery is only used when the computer is NOT connected to AC power.
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and
rechargeable batteries. For more information about recycling programs, go to
http://www.hp.com/
recycle.
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, then turn off any external devices.
4. Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board as
long as the system is plugged into an active AC outlet. You must disconnect the power cord to
avoid damage to the internal components of the computer.
5. Remove the computer access panel.
6. Locate the battery and battery holder on the system board.
NOTE: On some computer models, it may be necessary to remove an internal component to gain
access to the battery.
7. Depending on the type of battery holder on the system board, complete the following instructions
to replace the battery.
28 Hardware Upgrades ENWW
- Hardware Reference Guide 1
- About This Book 3
- Table of contents 5
- Hardware Upgrades 7
- Removing the Front Bezel 10
- Removing Bezel Blanks 11
- Replacing the Front Bezel 12
- Installing Additional Memory 13
- Installing DIMMs 14
- Drive Positions 20
- Installing Additional Drives 21
- Removing an Optical Drive 22
- Battery Replacement 34
- Installing a Security Lock 37
- HP Business PC Security Lock 38
- HP Chassis Security Kit 40
- A Electrostatic Discharge 41
- Optical Drive Precautions 43
- Shipping Preparation 43
Produits connexes et manuels pour Non HP Elite 7100 Microtower PC
(76 pages)
(89 pages)
(31 pages)
(91 pages)
(12 pages)
(93 pages)
(82 pages)
Non HP OMEN X 900-187na Manuel d'utilisateur
(46 pages)
(79 pages)
(80 pages)
(61 pages)
(82 pages)Desa CGN10R manuels
Manuels d'utilisation et guides de l'utilisateur pour Radiateurs Desa CGN10R.
Nous fournissons des manuels en pdf 1 Desa CGN10R à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels