Hp Dynamic Smart Array Controllers Manuel d'utilisateur

HP Dynamic Smart Array RAID Controller User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers and

Enabling and configuring the controller 10 9. Route the capacitor pack cable. For more information, see the server user guide. 10. Install or close

Installing device drivers and Management Agents 11 Installing device drivers and Management Agents Installing device drivers IMPORTANT: If neces

Installing device drivers and Management Agents 12 2. Confirm the boot device in RBSU. 3. Insert the operating system DVD. 4. Confirm that the ha

Installing device drivers and Management Agents 13 o For servers that support the B120i controller and have a SATA optical drive, Windows prompts fo

Installing device drivers and Management Agents 14 If the drive or logical volume is not available, select Load Driver. Then, insert the USB drive c

Installing device drivers and Management Agents 15 Installing device drivers (Red Hat Enterprise Linux 5 or 6) 1. Enable the controller ("Enab

Installing device drivers and Management Agents 16 7. The following screen appears. If the correct controller appears on the list, the driver has be

Installing device drivers and Management Agents 17 — Install the driver during operating system installation ("Installing the device driver du

Installing device drivers and Management Agents 18 a. Log in to ESX system console as root. b. Enter cd /tmp. c. Enter esxupdate -b <VIB> --

Replacing, moving, or adding hard drives 19 Replacing, moving, or adding hard drives Drive LEDs HP Dynamic Smart Array RAID controllers support driv

© Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties

Replacing, moving, or adding hard drives 20 CAUTION: Sometimes, a drive that has previously been failed by the controller may seem to be operation

Replacing, moving, or adding hard drives 21 Compromised fault tolerance CAUTION: When fault tolerance is compromised, data loss can occur. Howev

Replacing, moving, or adding hard drives 22 In RAID 5 configurations, you can replace one failed drive. When a physical drive fails, data that was o

Replacing, moving, or adding hard drives 23 • The amount of I/O activity during the rebuild operation • The rotational speed of the hard drives •

Replacing, moving, or adding hard drives 24 Verify that the replacement drive is of the correct capacity and is a supported model. If these factors

Replacing, moving, or adding hard drives 25 • If the other controller is connected to one or more arrays of configured logical drives, the total nu

Replacing, moving, or adding hard drives 26 o Migrate the hard drives (Windows) ("Migrating hard drives to an optional Smart Array controller—M

Replacing, moving, or adding hard drives 27 This action replaces the SATA connection. 9. Install components and cables removed previously. 10. Ins

Replacing, moving, or adding hard drives 28 IMPORTANT: Be sure to change only the prefixes. 4. Download and the latest Smart Array cciss driver

Replacing, moving, or adding hard drives 29 7. Install the access panel. 8. Reboot the server. At boot, press F5 for ACU or F10 for Intelligent Pro

Contents 3 Contents Overview ...

Software and configuration utilities 30 Software and configuration utilities Array Configuration Utility ACU is a browser-based utility with the fol

Software and configuration utilities 31 For more information or to download SPP, see the HP website (http://www.hp.com/go/spp). Intelligent Provisi

Software and configuration utilities 32 • POST messages Smart Array controllers produce diagnostic error messages (POST messages) at reboot. Many P

Support and other resources 33 Support and other resources Support and training information HP offers a number of additional software support servic

Electrostatic discharge 34 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Acronyms and abbreviations 35 Acronyms and abbreviations ACU Array Configuration Utility AMS agentless management services IML Integrated Manageme

Index 36 A activating an array 6 activation 6 Active Health System 31 ACU (Array Configuration Utility) 19, 22, 24, 30, 31, 32 adding drives

Index 37 R rebuild, abnormal termination of 23 rebuild, description of 22 rebuild, time required for 22 replacing hard drives 19 S Smart Arr

Contents 4 Support and training information ...

Overview 5 Overview Features Supported feature B120i controller B320i controller Drive support Hot-plug SATA drives and SATA SSD Yes Yes Hot-p

Enabling and configuring the controller 6 Enabling and configuring the controller Enabling the controller IMPORTANT: For HP ProLiant DL160, SL23

Enabling and configuring the controller 7 Installing the HP Smart Array SAS License Key When installed and activated on the B320i controller, the HP

Enabling and configuring the controller 8 FBWC module LEDs (B120i, B320i) The FBWC module has three single-color LEDs (one amber and two green).

Enabling and configuring the controller 9 1. Power down the server. 2. Remove all power: a. Disconnect each power cord from the power source. b.