Hp NonStop G-Series Manuel d'utilisateur Page 98
- Page / 146
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Switch Command Interface (SWCI)
ServerNet Nomadic Disk User’s Guide—425485-001
6-34
Command Execution Error Messages
Cause. An an error occurred during an attempt to read the command file. err-num is
the Guardian file-system error number that occurred.
Effect. The command file is not executed.
Recovery. Refer to the Guardian Procedure Errors and Messages Manual for recovery
from the file-system error.
Cause. An error occurred during an attempt to read the switch module device.
err-num is the Guardian file-system error number that occurred.
Effect. The command is not executed. SWCI waits for the next command.
Recovery. Refer to the Guardian Procedure Errors and Messages Manual for recovery
from the file-system error. Then retry the command.
Cause. An error occurred during the wait for a response message from the SCC for a
previously issued SWITCH command. err-num is the Guardian file-system error
number that occurred.
Effect. The command is not executed. SWCI waits for the next command.
Recovery. Refer to the Guardian Procedure Errors and Messages Manual for recovery
from the file-system error. Then retry the command.
Cause. An error occurred during an attempt to send a command through the device to
the attached SCC. err-num is the Guardian file-system error number that occurred.
Effect. The command is not executed. SWCI waits for the next command.
Recovery. Refer to the Guardian Procedure Errors and Messages Manual for recovery
from the file-system error. Then retry the command.
***ERROR*** Guardian error err-num on access to obey file
file-name.
***ERROR*** Guardian error err-num on read of switch comm
port.
***ERROR*** Guardian error err-num while awaiting switch
response.
***ERROR*** Guardian error err-num while sending switch
command.
- ServerNet Nomadic Disk 1
- User’s Guide 1
- Document History 2
- Index Examples Figures Tables 3
- 4. Switch Modules 4
- 5. Switchovers 4
- Contents 5
- A. Part Numbers 6
- Table 6-1 7
- Summary of SWCI Commands 6-8 7
- Table A-1 7
- What’s New in This Guide 10
- New and Changed Information 10
- About This Guide 11
- Where to Get More Information 12
- Your Comments Invited 12
- Notation Conventions 13
- Remote Disk Drive Mirroring 18
- Switchover 19
- VST101.vsd 20
- Supported Database Products 21
- Unsupported Database Products 22
- Nomadic Disk Software 24
- Nomadic Disk Hardware 25
- Disk Manager 29
- Nomadic Disk Manager Files 30
- > VOLUME $SYSTEM.NOMADIC 31
- > OBEY CREATOR 31
- CONFIG^FILE 33
- Configuration File Examples 34
- ADD DEFINE Statement 38
- ADD SEGMENT Statement 39
- PROCESS Statement 40
- PROCESS FUP CPU 3, PRI 151 41
- SET PATH Statement 42
- SET VOL Statement 43
- Switch Modules 45
- Switch Controller Card 47
- SCC Key Switch 48
- SCC Temperature Sensors 48
- SCC LEDs 49
- Alarm Port 50
- Switch Card 51
- Switch Card Toggle Switches 52
- Switch Card LEDs 53
- Switchovers 55
- Preparing for a Switchover 56
- Switchover Examples 57
- Position 58
- Planned Switchovers 59
- On Backup Node \BCK 60
- Unplanned Switchovers 61
- Switchback 62
- On the Primary Node \PRI 63
- > SWCI $SWITCH1.#PRI 66
- SWCI $SWITCH1.#PRI> STATUS 66
- Communications 67
- Switch Module Device Name 69
- Starting SWCI 70
- Stopping SWCI 71
- SWCI Commands 72
- ALARM Command 73
- Consideration 73
- LOCK Command 75
- LOG Command 76
- OBEY Command 77
- SELFTEST Command 78
- STATUS Commands 79
- SWITCH Command 87
- UNLOCK Command 89
- Considerations 89
- SWCI Messages 90
- Startup message not found 92
- Environmental Alert Messages 114
- Considerations 116
- Nomadic Disk Manager Commands 117
- Command Description Page 118
- ASSUME Command 119
- Examples 119
- DOWN Command 120
- EXIT Command 121
- GIVE Command 122
- HELP Command 124
- HISTORY Command 125
- LISTDEV Command 126
- LISTOPENS Command 127
- OUT Command 128
- RESET Command 129
- SEGMENTS Command 130
- SQL Command 131
- STATUS Command 131
- TAKE Command 133
- TMF Command 135
- UP Command 135
- VOLUMES Command 136
- Part Numbers 137
- Mirroring 139
Produits connexes et manuels pour Matériel informatique Hp NonStop G-Series
(100 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels