Hp ProLiant ML350p Gen8 Server Manuel d'utilisateur Page 106
- Page / 145
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Hardware options installation 106
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
1. Do one of the following:
o For tower models, open and remove the bezel ("Remove the tower bezel" on page 21).
o For rack models, if installed, remove the security bezel (on page 21).
2. Power down the server (on page 20).
3. Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
4. Do one of the following:
o For tower models, place the server on a flat, level surface with the access panel facing up.
o For rack models, extend the server from the rack (on page 24).
5. Remove the access panel (on page 23).
6. Remove the air baffle (on page 25).
7. If installed, remove the PCI card from slot 9 ("System board components" on page 11).
CAUTION: Any attempt to remove an installed TPM from the system board breaks or disfigures
the TPM security rivet. Upon locating a broken or disfigured rivet on an installed TPM,
administrators should consider the system compromised and take appropriate measures to ensure
the integrity of the system data.
8. Install the TPM board. Press down on the connector to seat the board ("System board components" on
page 11).
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Rear panel components 9
- Rear panel LEDs 10
- System board components 11
- DIMM slots 12
- System maintenance switch 13
- NMI functionality 13
- Systems Insight Display LEDs 14
- SAS and SATA device numbers 15
- • SFF drives 16
- • LFF drives 16
- RPS riser board connectors 18
- Item Connector Description 19
- Operations 20
- Remove the security bezel 21
- Install the security bezel 21
- Remove the tower bezel 21
- Remove the rack bezel 22
- Install the rack bezel 23
- Remove the access panel 23
- Install the access panel 24
- Remove the air baffle 25
- Install the air baffle 26
- Remove the fan 27
- Remove the fan cage 27
- Remove the optical drive 28
- Operations 30 30
- Rack planning resources 31
- Optimum environment 31
- Temperature requirements 32
- Rack warnings 33
- Server warnings and cautions 34
- Installing hardware options 35
- Setting up a tower server 35
- Setup 37 37
- Setup 38 38
- Setup 40 40
- Setup 41 41
- Registering the server 44
- Introduction 45
- Mini-SAS cable option 45
- Cable routing to box 1 46
- Cable routing to box 2 46
- Second processor option 47
- Processor upgrade 53
- 8. Remove the heatsink 54
- Memory options 59
- HP SmartMemory 60
- Population order 61
- Installing a DIMM 61
- DIMM identification 63
- Memory configurations 63
- Advanced ECC 64
- Online spare population 65
- Optical drive cage option 66
- Remove the blank from box 3 67
- Optical drive option 69
- Hot-plug SAS drive options 72
- Installing a hot-plug drive 73
- Expansion board option 74
- Graphic card option 77
- Controller option 81
- Redundant fans option 85
- Six-bay LFF drive cage 92
- Cabling 109
- Media device data cabling 110
- Optical drive cabling 110
- Server mode 111
- HP product QuickSpecs 111
- HP iLO Management 111
- Active Health System 112
- Intelligent Provisioning 113
- HP Insight Diagnostics 114
- HP Service Pack for ProLiant 115
- HP ROM-Based Setup Utility 115
- Using RBSU 116
- Auto-configuration process 116
- Boot options 117
- Configuring AMP modes 117
- Utilities and features 118
- Automatic Server Recovery 119
- USB support 119
- Redundant ROM support 119
- Keeping the system current 120
- ProLiant servers 121
- Troubleshooting 122
- Battery replacement 123
- Battery replacement 124 124
- Regulatory information 125
- Electrostatic discharge 126
- Specifications 127
- Specification Value 129
- Support and other resources 131
- Customer Self Repair 133
- Reparo feito pelo cliente 135
- Acronyms and abbreviations 139
- Documentation feedback 142
- Index 143 143
- Index 144 144
- Index 145 145
Produits connexes et manuels pour Matériel informatique Hp ProLiant ML350p Gen8 Server
(42 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels