HP Hybrid POS Printer with MICR II Manuel d'utilisateur Page 1

HP Hybrid Printer IIUser Guide

2 Setting up the printerChoosing a location for the printerThe printer requires minimum counter space and may be set on or near the POS computer.Do no

Removing the packing materialsThe packing materials protect the printer and help prevent damage during shipment.1. Remove the cardboard supports only

3. Place the roll into the paper bucket with the paper unrolling from the bottom of the roll, and with a few inches of paper extending over the cabine

5. Remove the excess paper by tearing it against the tear-o blade.6. Press the paper feed button to advance the paper if necessary.Removing and insta

Installing a new ribbon cassette1. Open the front cover (1) by grasping the cover on each side near the top and swinging it toward you.2. Unwrap the n

Connecting the cablesNOTE: Place the printer on a level surface and position it in a location that allows access to cables and provides ample room to

Testing the printerThis test prints a complete list of printer settings on a diagnostic form and partially cuts the paper. Instructions at the end of

Test procedure1. To run the test, open the receipt cover (1); then, while holding down the paper feed button (2), close the receipt cover (3).2. When

–Normal–Data scope–Receipt test–Slip test–MICR test–Check ip test●Emulation/software options–Printer emulations- A776II native- A756 emulation–Print

Conguring the printerIMPORTANT: When changing any of the printer settings, be extremely careful to avoid inadvertently changing other settings that m

© Copyright 2017 HP Development Company, L.P.Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/o

●Indicate Yes with a long click. (Press and hold the paper feed button for more than one second.)●Indicate No with a short click. (Press the paper fee

●O, normal mode (data scope mode disabled)●Data scope mode (enabled)NOTE: Press the paper feed button for at least one second to validate the selecti

Enabling or disabling slip test modeThe slip test mode veries proper printing on a slip. Slip test is enabled or disabled by selecting the Diagnostic

Setting the printer emulations and software optionsPrinter emulations determine what commands are available to the printer. To change the printer emul

Sets the printer to delete number (N) of leading spaces in the slip format for compressed print.●Compressed mode: Disabled/EnabledTurns on compressed

Allows the user to enable or disable the check reader.●MICR dual pass optionThis feature allows the printer to attempt a second reading of the check M

3 Operating the printerPrinting on forms or checksSeveral types of transactions may require the insertion of a check or other form into the printer:●C

Drop-in printing method1. Insert the form or check into the slot from the top or side with the print side toward you. You may feel a slight resistance

Top or side slip-in printing - no perforation holes to right side:Verifying and validating checksThe printer’s MICR check reader enables check verica

2. Slide the check straight forward (2) into the printer until the green slip-in light on the top right edge of the printer comes on, indicating both

About This GuideThis guide provides information on setting up and using the HP Hybrid Printer II.WARNING! Indicates a hazardous situation that, if not

Allowable duty cycle (measured over one minute of continuous printing)Amount of solid coverageAmbient temperature 25°C (77°F) 35°C (95°F) 50°C (122°F

Cleaning the printerCleaning the printer cabinetClean the outside cabinet as needed, using any household cleaner made for plastics. You may want to te

6. Press the paper feed button to advance the paper, if necessary.7. Run a diagnostics test to assure the printer is communicating with the POS comput

4 Paper requirementsThermal paperThe printer requires qualied paper with the following dimensions:●Width: 80 ± 5 mm (3.15 ± 0.2 in)●Diameter: 83 mm (

Qualied manufacturer Paper grade20 Cummings St.Ware, MA 01082–2002Voice: (888) 526–9254Fax: (413) 731–8864http://www.kanzakiusa.com/P31023 (was P–310

Qualied manufacturer Paper gradeFax: (904) 646-4530http://thermalsolutionsinternational.comTwo-color paperQualied manufacturer Paper gradeMitsubishi

The slip sensors that activate the slip-in light use a reective photo sensor.●Do not use paper that has holes or dark areas with low reection (less

IMPORTANT: Use of other than an approved ribbon cassette can void all warranties and cause damage from jamming and other ribbon problems.The printer u

A TroubleshootingBecause of the design of the printer, it requires virtually no periodic servicing. However, if problems do occur, they can usually be

3. Test the receipt printer or slip printer by performing a sample test print. See Testing the printer on page 10.4. Determine if the condition is wit

iv About This Guide

Online paper status error light ashesProblem Possible cause SolutionReceipt or front cover is open. Close the receipt cover or front cover. The print

Check print quality poorProblem Possible cause SolutionForms print is light or spotty. Form is not inserted correctly. Refer to Printing on forms or c

Receipt print quality poorProblem Possible cause SolutionPaper setting is incorrect. Check diagnostics setting.Printer will not perform two-color prin

KnifeProblem Possible cause SolutionReceipt is not cut. Paper is jammed. Open the receipt cover, inspect the knife, and clear any jammed paper.All oth

B Technical specicationsHP Hybrid Printer IIPrinter specications Receipt station Print method Direct thermal, 203 DPICharacter cell size 13 x 24,

Printer specications Check read rate 99% minimumParsing formats E-13B only. Programmable to any formatDimensions and weight Height 167.64 mm/6.6 in

Table of contents1 Product features ...

Paper ...

1 Product featuresThe HP Hybrid Printer II is a small, eicient point of sale printer for retailers. It features fast black-and-white or ColorPOS® rec

●8 MB ash memory, 8 K buer●8 dots/mm print resolution with up to 350 mm/second throughput speed●Selectable 44 (standard) or 56 (compressed) columns

Identifying rear componentsRear components1 USB power port—Connects the printer to the POS computer and provides power to the printer2 Cash drawer por