HP StorageWorks Enterprise File Services WAN Accelerator Guide de l'utilisateur Page 86
- Page / 124
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
80 7 - WCCP DEPLOYMENTS
Router(config)# ip wccp 90 password <your_password>
2. On the HP EFS WAN Accelerator, at the system prompt, enter the following
command:
client-SH (config) # wccp service-group 90 routers 10.1.0.1 password
<your_password>
NOTE: The same password must be set on the HP EFS WAN Accelerator and the router.
Multicast If you add multiple routers and HP EFS WAN Accelerators to a service group, you can
configure them to exchange WCCP protocol messages through a multicast group.
Configuring a multicast group is advantageous because if a new router is added, it does
not need to be explicitly added on each HP EFS WAN Accelerator.
To configure multicast
groups on your router
• On your router, at the system prompt, enter the following set of commands:
Router> enable
Router# configure terminal
Router(config)# ip wccp version 2
Router(config)# ip wccp 90 group-address 224.0.0.3
Router(config)# interface fastEthernet 0/0
Router(config-if)# ip wccp 90 redirect in
Router(config-if)# ip wccp 90 group-listen
Router(config-if)# end
Router#
TIP: Enter configuration commands, one per line. End each command with CTRL-Z.
To configure multicast
groups on the HP EFS
WAN Accelerator
• On the client-side HP EFS WAN Accelerator, at the system prompt, enter the
following set of commands:
client-SH > enable
client-SH # configure terminal
client-SH (config) # wccp enable
client-SH (config) # wccp mcast-ttl 10
client-SH (config) # wccp service-group 90 routers 224.0.0.3
client-SH (config) # write memory
client-SH (config) # exit
TCP Port
Redirection
By default, all TCP ports are redirected, but the HP EFS WAN Accelerator can be
configured to tell the router to redirect only certain TCP source or destination ports. A
maximum of 7 ports can be specified per service groups.
NOTE: You do not need to configure source and destination ports on the router.
To configure TCP port
redirection
• On the client-side HP EFS WAN Accelerator, at the system prompt, enter the
following command:
- HP StorageWorks 1
- Contents 3
- Introduction 7
- Organization of 8
- This Guide 8
- Document 9
- Conventions 9
- Antivirus Compatibility 10
- Additional Resources 11
- 6 INTRODUCTION 12
- Contacting HP 13
- HP Storage Web Site 13
- INTRODUCTION 14
- Designing an HP EFS WAN 15
- Accelerator Deployment 15
- How Does SDR 16
- Transaction 17
- Prediction 17
- Definition of Terms 19
- Bypass Mode 19
- Failover Mode 20
- In-Path Deployments 23
- Basic Steps 24
- (Client-Side) 24
- (Server-Side) 26
- 24 2 - IN-PATH DEPLOYMENTS 30
- Virtual In-Path Network 31
- Out-of-Path Network 35
- Configuring Connection 45
- Forwarding 45
- Neighbors in 46
- Connection 46
- Using the CLI 50
- Policy-Based Routing 51
- Introduction to PBR 52
- Overview of CDP 52
- Version 12.2(17d) SXB1 53
- Deployments With PBR 55
- PBR Using the 57
- Management 57
- Attached to an Inside Router 61
- PBR Between VLANs 61
- To configure the Cisco 64
- 59 65
- Autodiscovery, and CDP 66
- 61 67
- Troubleshooting 68
- WCCP Deployments 69
- Introduction to WCCP 70
- EPLOYMENTS 71
- 7 - WCCP DEPLOYMENTS 73
- A Basic WCCP Configuration 74
- Configuring the 75
- Client-Side HP 75
- EFS WAN 75
- Accelerator 75
- 74 7 - WCCP DEPLOYMENTS 80
- Dual WCCP Deployment 82
- 77 83
- To configure the 84
- WCCP (6209) router 84
- Additional WCCP Features 85
- TCP Port 86
- Redirection 86
- Specific Traffic 87
- Failover 87
- Support 87
- Introduction to PFS 89
- PFS Terms 90
- PFS Operating 91
- How Does PFS Work? 92
- When to Use 93
- When to use 94
- Global Mode 94
- Configuration 94
- Checklist for 94
- 100
- 8 - PROXY FILE SERVICE 101
- To view share status 102
- RADIUS and TACACS+ 103
- Authentication 103
- FreeRADIUS 104
- Configuring a TACACS+ Server 106
- Configuring 107
- TACACS+ 109
- 105 111
- 7. Click Save 111
- Serial Cluster and Cascade 113
- Deployments 113
- Figure 10-1. Serial Cluster 114
- A Basic Serial 115
- Cluster 115
- Deployment 115
- Cascade Deployment 117
- Fixed-Target 118
- Glossary 119
- 114 GLOSSARY 120
- 116 GLOSSARY 122
- INDEX 123
Produits connexes et manuels pour Routeurs HP StorageWorks Enterprise File Services WAN Accelerator
Routeurs HP EX495 Manuel d'utilisateur
(331 pages)
(331 pages)
Routeurs HP F150 Manuel de démarrage rapide
(26 pages)
(26 pages)
Routeurs HP 10BASE-T Manuel d'installation
(104 pages)
(104 pages)
Routeurs HP JL066AABA Fiche technique
(12 pages)
(12 pages)
Routeurs HP JG409A#ABB Fiche technique
(46 pages)
(46 pages)
Routeurs HP JF240A Fiche technique
(23 pages)
(23 pages)
Routeurs HP JF231A Fiche technique
(20 pages)
(20 pages)
Routeurs HP JD026A Fiche technique
(9 pages)
(9 pages)
Routeurs HP JE459A Fiche technique
(7 pages)
(7 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels