HP PROCURVE 2300 Manuel d'utilisateur Page 30
- Page / 270
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
19
Enhancements in Release F.05.05 through F.05.70
Enhancements in Release F.05.05 through F.05.60
Viewing the Syslog Configuration
Configuring Syslog Logging
1. If you want to use a Syslog server for recording Event Log messages:
a. Use this command to configure the Syslog server IP address and enable Syslog logging:
ProCurve(config)# logging < ip-addr >
Using this command when there are no Syslog server IP addresses already configured
enables messaging to a Syslog server.
b. Use the command in step “a” to configure any additional Syslog servers you want to use, up
to a total of six.
Example: Suppose there are no Syslog servers configured on the switch (the default). Configuring
one Syslog server enables Event Log messages to be sent to that server. (Refer to Figure 5 below.)
Figure 5. Example of Configuring Syslog Operation
Syntax: show debug
This command displays the currently configured Syslog log-
ging destination(s) and logging facility. For examples of show
debug output, refer to figure 5 on page 19.
ProCurve(config)# show debug
Debug Logging
Destination: None
Enabled debug types:
None are enabled.
ProCurve(config)# logging 10.250.125.69
ProCurve(config)# show debug
Debug Logging
Destination:
Logging --
10.250.125.69
Facility = user
Enabled debug types:
event
Displays the default debug
configuration. (There are no
Syslog server IP addresses
When the logging command
configures a Syslog IP address, the
switch automatically enables
sending Event Log messages to the
Syslog address and the user
facility on the Syslog server.
- Release Notes: 1
- Disclaimer 3
- Warranty 3
- Contents 4
- Software Management 12
- TFTP Download from a Server 13
- Implementation of LLDP 18
- LLDP Terminology 18
- General LLDP Operation 19
- LLDP Configuration Options 19
- LLDP Standards Compatibility 20
- LLDP Operating Rules 21
- LLDP Operation and Commands 22
- Viewing LLDP-detected Devices 23
- Disable Auto-MDIX 25
- New Console Option 26
- Syslog Overview 27
- Syslog Operation 27
- ■ Switch Series 2800 29
- Configuring Syslog Logging 30
- Operating Notes for Syslog 31
- General Features 41
- How 802.1X Operates 42
- Authenticator Operation 42
- Note on 802.1X and LACP 46
- 802.1X Open VLAN Mode 55
- Introduction 55
- Only 802.1X Devices 66
- Connections to Other Switches 68
- Status Indicator Meaning 76
- ■ The switch reboots 77
- IGMP Version 3 Support 82
- Friendly port names assigned 86
- Friendly Port Name 87
- ■ 3DES (168-bit) 90
- ■ DES (56-bit) 90
- Prerequisite for Using SSH 91
- Public Key Format Requirement 91
- Host Public Key 97
- Note on the Public Key Format 98
- Hexadecimal "Hash" 100
- Public Key 100
- Phonetic "Hash" of 100
- Switch’s Public Key 100
- ■ Execute no ip ssh 101
- Note on Port Number 102
- Bit Size Public Index 107
- Note on Public Keys 109
- Troubleshooting SSH Operation 112
- ■ Serial port (Console) 113
- ■ Telnet 113
- ■ Port-Access 113
- Terminology 114
- Preparation: 115
- The switch now allows 119
- Telnet and SSH 119
- Local Authentication Process 124
- Configuring RADIUS Accounting 125
- ■ IP address: 10.33.18.151 129
- ■ Start-Stop: 131
- ■ Stop-Only: 131
- Viewing RADIUS Statistics 132
- RADIUS Authentication 135
- RADIUS Accounting 136
- as both the primary 138
- Global RADIUS Encryption Key 139
- Configuration File Downloads 140
- Session 2 is an active 147
- Telnet session 147
- The kill 2 command 147
- Overview 148
- Configuring RSTP 150
- Note on Path Cost 156
- The asterisk indicates that 164
- 5. Press 166
- Operating Notes 171
- Fast-Uplink Troubleshooting 172
- Access Security 176
- General System Requirements 179
- TACACS+ Operation 180
- Note on Privilege Levels 181
- First-Choice TACACS+ Server 190
- How Authentication Operates 192
- Using the Encryption Key 194
- General Operation 194
- Authentication 195
- Messages 196
- 2. Switch Configuration 199
- 1. System Information 199
- TimeP Time Synchronization 200
- SNTP Time Synchronization 200
- Time Protocol Operation 200
- Table 15. SNTP Parameters 202
- – TIMEP 203
- Broadcast as the SNTP mode 206
- Broadcast 208
- Table 16. Timep Parameters 210
- – TIMEP (the default) 211
- Time Sync 213
- Manual mode enables 214
- DHCP as 215
- Address Prioritization 216
- Configured 218
- Control (IGMP) 219
- Fast-Leave IGMP 221
- Forced Fast-Leave IGMP 223
- 2 at the 224
- 7 specifies port 7 224
- Verification 225
- Querier Operation 226
- Switch Memory Operation 227
- Addresses Across a Reboot 228
- Configuration Guide 231
- Time Protocol Changes 232
- Passwords 233
- Software Fixes 237
- Release F.01.08 240
- Release F.01.10 240
- Release F.02.02 240
- Release F.02.03 242
- Release F.02.09 246
- Release F.02.10 246
- Release F.02.11 246
- Release F.02.12 247
- Release F.02.13 247
- Release F.04.08 249
- Release F.05.14 254
- Release F.05.17 258
- Release F.05.18 258
- Release F.05.22 259
- Release F.05.33 263
- Release F.05.34 263
- Release F.05.52 265
- Release F.05.55 266
- Release F.05.59 267
- Release F.05.60 267
- Release F.05.61 267
- Release F.05.68 268
- Release F.05.69 269
- Release F.05.70 269
Produits connexes et manuels pour Logiciel HP PROCURVE 2300
Logiciel HP B6191-90028 Manuel d'utilisateur
(115 pages)
(115 pages)
Logiciel HP 4000M Manuel d'utilisateur
(304 pages)
(304 pages)
Logiciel HP Netsight Manuel d'utilisateur
(238 pages)
(238 pages)
Logiciel HP P9500 Manuel d'utilisateur
(494 pages)
(494 pages)
Logiciel HP X9320 Manuel d'utilisateur
(125 pages)
(125 pages)
Logiciel HP AA-RS29F-TE Manuel d'utilisateur
(141 pages)
(141 pages)
Logiciel HP D2D Manuel d'utilisateur
(93 pages)
(93 pages)
Logiciel HP XP12000 Manuel d'utilisateur
(118 pages)
(118 pages)
Logiciel HP SENTRY Manuel d'utilisateur
(113 pages)
(113 pages)
Logiciel HP 6500 Series Manuel d'utilisateur
(265 pages)
(265 pages)
Logiciel HP 3PAR Manuel d'utilisateur
(63 pages)
(63 pages)
Logiciel HP M208 Manuel d'utilisateur
(224 pages)
(224 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels