Hp MSA 2040 SAN Storage Manuel d'utilisateur Page 29
- Page / 94
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Powering on/powering off 29
Connect power cable to DC power supply
Locate two DC power cables that are compatible with your controller enclosure.
Figure 18 DC power cable featuring sectioned D-shell and lug connectors
See Figure 18 and the illustration at left (in Figure 17) when performing the following steps:
1. Verify that the enclosure power switches are in the Off position.
2. Connect a DC power cable to each DC power supply using the D-shell connector.
Use the UP> arrow on the connector shell to ensure proper positioning (see adjacent
left side view of D-shell connector).
3. Tighten the screws at the top and bottom of the shell, applying a torque between 1.7
N-m (15 in-lb) and 2.3 N-m (20 in-lb), to securely attach the cable to the DC power
supply module.
4. To complete the DC connection, secure the other end of each cable wire component
of the DC power cable to the target DC power source.
Check the three individual DC cable wire labels before connecting each cable wire lug to its power
source. One cable wire is labeled ground (GND) and the other two wires are labeled positive (+L) and
negative (-L), respectively (shown in Figure 18 above).
CAUTION: Connecting to a DC power source outside the designated -48V DC nominal range
(-36V DC to -72V DC) may damage the enclosure.
Connect power cord to legacy AC power supply
Obtain two suitable AC power cords: one for each AC power supply that will connect to a separate power
source. See the illustration at right [in Figure 17 (page 28)] when performing the following steps:
1. Verify that the enclosure power switches are in the Off position.
2. Identify the power cord connector on the power supply, and locate the target power source.
3. For each power supply, perform the following actions:
a. Plug one end of the cord into the power cord connector on the power supply.
b. Plug the other end of the power cord into the rack power source.
4. Verify connection of primary power cords from the rack to separate external power sources.
Power cycle
To power on the system:
1. Power up drive enclosure(s).
Press the power switches at the back of each drive enclosure to the On position. Allow several seconds
for the disks to spin up.
2. Power up the controller enclosure next.
Press the power switches at the back of the controller enclosure to the On position. Allow several
seconds for the disks to spin up.
To power off the system:
1. Stop all I/O from hosts to the system [see "Stopping I/O" (page 53)].
2. Shut down both controllers using either method described below:
+L
GND
-L
+L
GND
-L
+L
GND
-L
+L
GND
-L
Connector pins (typical 2 places)
Connector (front view)
Ring/lug connector (typical 3 places)
D-shell
(left side view)
- HP MSA 2040 1
- User Guide 1
- Contents 3
- 4Contents 4
- Contents 5 5
- 6Contents 6
- 8Figures 8
- Tables 9 9
- 10 Tables 10
- 1Overview 11
- Features and benefits 12
- 2Components 13
- SERVICE−1SERVICE−2 14
- PORT 1 PORT 2 PORT 3 PORT 4 15
- Drive enclosures 16
- Transportable CompactFlash 17
- Supercapacitor pack 18
- Upgrading to MSA 2040 18
- 3Installing the enclosures 19
- 20 Installing the enclosures 20
- Testing enclosure connections 27
- Powering on/powering off 27
- Power cycle 29
- 30 Installing the enclosures 30
- 4 Connecting hosts 31
- 10GbE iSCSI protocol 32
- 1 Gb iSCSI protocol 32
- MSA 2040 SAS 33
- One server/one HBA/dual path 34
- Dual controller configuration 35
- Cabling for replication 37
- Host ports and replication 38
- Updating firmware 41
- 42 Connecting hosts 42
- Device description 43
- Obtaining IP values 43
- Host Interface 45
- Not Shown 45
- IP-address 46
- Workaround 47
- 6 Basic operation 49
- 50 Basic operation 50
- 7Troubleshooting 51
- Performing basic steps 52
- Stopping I/O 53
- Diagnostic steps 54
- Transporting cache 58
- 60 Troubleshooting 60
- Can you replicate a volume? 64
- Can you view remote systems? 64
- Sensor locations 65
- Power supply sensors 65
- Cooling fan sensors 65
- Temperature sensors 66
- 8 Support and other resources 67
- Websites 68
- Prerequisites 68
- Troubleshooting resources 68
- Typographic conventions 69
- Rack stability 69
- Customer self repair 70
- Product warranties 70
- 9 Documentation feedback 71
- 72 Documentation feedback 72
- A LED descriptions 73
- Disk drive LEDs 75
- Rear panel LEDs 76
- = FC LEDs 77
- = iSCSI LEDs 77
- SAS 1 SAS 2 79
- SAS 3 SAS 4 79
- Power supply LEDs 80
- D2700 6Gb drive enclosure 81
- 82 LED descriptions 82
- Safety requirements 83
- Management host requirements 84
- Physical requirements 85
- Environmental requirements 86
- Electrical requirements 86
- C Electrostatic discharge 87
- 88 Electrostatic discharge 88
- D SFP option for host ports 89
- Verify component operation 90
- Index 91 91
- 92 Index 92
- HP MSA 2040 User Guide 93 93
- 94 Index 94
Produits connexes et manuels pour Stockage Hp MSA 2040 SAN Storage
Stockage Hp SAN Manuel d'utilisateur
(30 pages)
(30 pages)
(91 pages)
(37 pages)© 2020, manymanuals.fr. Tous droits réservés | 3.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels