HP L2151W Manuel d'utilisateur

L2151w/L2151ws LCD Monitor User’s Guide

10 Using the Monitor Operating Instructions Control buttons are located on the front of the panel, as shown in the following illustration. Use the

11 External Controls A Auto button Automatically fine-tunes the image quality. B Menu button Opens, selects, or exits the OSD menu. C – (minus

12 Settings Setting the Optimal Resolution The recommended resolution for this monitor is 1920 x 1080.To configure the monitor to this resolution, c

13 Adjusting On-Screen Display Settings Use the OSD menu to adjust the screen image and change settings. To access the OSD menu: 1 If the monitor is n

14 OSD Menu The table below shows the OSD menus and their functions at each level. OSD Menu Levels Level 1 Level 2 Level 3 Factory Preset Brightnes

15 OSD Menu Levels (continued) Level 1 Level 2 Level 3 Factory Preset OSD Control Horizontal OSD Position Adjustment Scale Y Vertical OSD Posi

16 OSD Menu Levels (continued) Level 1 Level 2 Level 3 Factory Preset Default DVI / VGA Selection Y Auto-Switch Source On / Off Selection Y

17 Installing Drivers and Using the Auto-Adjustment Feature Downloading Drivers and Software To download the latest version of drivers and software

18 Technical Support FAQs Technical Support FAQs (Frequently Asked Questions) Problem & Question Possible Solutions Power LED is not on. y Mak

19 Technical Support FAQs (Frequently Asked Questions) (continued) Problem & Question Possible Solutions Missing one of the primary colors (red,

The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing her

20 Specifications All specifications represent the typical specifications provided by HP’s component manufacturers; actual performance may vary eith

21 Preset Display Modes Preset Pixel Format Horz Freq (kHz) Horz Polarity Vert Freq (Hz) Vert Polarity Pixel Clk (MHz) Source 1 640 x 480 31.469

22 Power Cord Set Requirements The monitor power supply is provided with automatic line switching (ALS). This feature allows the monitor to operate o

23 Plug and Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to info

24 Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hew

25 European Union Regulatory Notice This product complies with the following EU directives: y Low Voltage Directive 2006/95/EC y EMC Directive 2004/10

26 Disposal of Waste Equipment by Users in Private Households in the European Union This symbol on the product or on its packaging indicates that th

27 Japanese Power Cord Notice Japanese Material Content Declaration A Japanese regulatory requirement, defined by Specification JIS C 0950, 2005, m

28 ENERGY STAR® Qualification HP Displays marked with the ENERGY STAR® certification mark meet the requirements of the U.S. Environmental Protection

29

3 Preface About This Guide This guide is intended for anyone who uses the HP L2151w/L2151ws LCD Monitor. It describes the monitor’s features, setup,

30

Part number: 585342-001

4 Safety and Maintenance Guidelines Important Safety Information The power adapter and cord are designed for use with your HP monitor . The adapter

5 Maintenance Guidelines To enhance the performance and extend the life of your monitor: y Do not open your monitor cabinet or attempt to service this

6 Setup Base and Tilt Attaching the Base 1 Set the panel face down on a flat , protected surface , such as a table top. 2 Using both hands , align t

7 Removing the Base 1 Set the panel face-down on a flat, protected surface. 2 Squeeze the tabs in the bottom of the base to release the lock. 3 Remove

8 Cables Attaching the Cables 1 Turn off your computer. 2 If you are attaching a VGA cable, connect one end of the 15-pin D-Sub VGA cable (blue conn

9 4 Connect the power cord and adapter first, and then connect one end of the power adapter to the back of the monitor and plug the other end into a g