HP Integrity rx2600 Spécifications Page 103
- Page / 166
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
HP Integrity rx2600 server and HP workstation zx6000 Operation and Maintenance Guide 103
Removing and Replacing Components
Removing and Replacing System Batteries
Servers with an iLO MP card have two batteries. Servers that do not have an iLO MP card only
have one battery.
WARNING: There is a danger of explosion if the battery is incorrectly installed. For your safety, never
attempt to recharge, disassemble, or burn an old battery. Replace the battery with the same or equivalent
type, as recommended by the manufacturer.
The battery in this server is a lithium battery that does not contain any heavy metals. However, to protect
the environment, do not dispose of batteries in household waste. Return used batteries either to the shop
from where you bought them, to the dealer from whom you purchased the server, or to HP so that they
can be recycled or disposed of in the correct way. Returned batteries are accepted free of charge.
Removing the System Battery
To remove the system battery, follow these steps:
1. Power off the server, disconnect all power and external cables and remove the server covers.
2. Remove the processor airflow guide.
3. Lift up on the battery and push on the back of it with a flat-head screwdriver to remove the
battery from its holder.
CAUTION: Lift the battery just high enough to clear its holder. Too much stress on the battery holder
retaining clip may break it.
Remove the System Board Battery
Replacing the System Battery
To replace the system battery, follow these steps:
1. Lift up on the battery holder retaining clip with a flat-head screwdriver and slide the battery
into its holder. The positive
(+) side of the battery should face up.
CAUTION: Lift the battery just high enough to clear its holder. Too much stress on the battery holder
retaining clip may break it.
2. Replace the processor airflow guide.
- HP zx6000 Workstation 1
- Contents 3
- About this Document 9
- Intended Audience 9
- Publishing History 9
- Document Organization 10
- Typographic Conventions 11
- Related Documents 11
- HP Encourages Your Comments 12
- Overview 13
- Server Features 14
- Feature Description 15
- Physical Characteristics 16
- Power Specifications 17
- Environmental Specifications 18
- Front Panel 19
- Rear Panel 20
- System Configuration 21
- Using the EFI Shell 22
- You see this prompt: 23
- Command Descriptions 25
- EFI Scripts 28
- 2. Press Enter 29
- Error Handling in Scripts 30
- Comments in Script Files 30
- Boot from a File 31
- Add a Boot Option 32
- Delete Boot Option(s) 33
- Change Boot Order 33
- Manage BootNext Setting 33
- Set Auto Boot TimeOut 34
- Security/Password Menu 38
- Resetting Passwords 40
- Password Reset Jumper 41
- Accessing the iLO MP 43
- Enter for initial access 47
- Using the iLO MP Commands 48
- Running Commands from Menus 49
- Command Syntax 49
- Accessing the BMC 53
- Simple Commands 55
- IPMI Commands 55
- Command Categories 57
- Chassis Commands 57
- Sensor/Event Commands 58
- Application Commands 58
- Storage Commands 59
- Firmware Upgrades 60
- Gather Your Tools 64
- Server Covers and Bezel 65
- Removing the Left-side Cover 66
- Removing the Top Cover 66
- Top Cover Alignment Mark 67
- Replacing the Top Cover 67
- Replacing the Side Cover 67
- Rack-Mount Server 68
- Releasing the Rack Latches 69
- Guide-rail Release Clips 69
- Removing the Front Bezel 70
- Replacing the Front Bezel 70
- Hot-Pluggable Devices 71
- Replacing a System Fan 72
- Removing a Power Supply 73
- Hard Drives 74
- Removing a Hard Drive 75
- Airflow Guides 76
- Removing and Replacing Memory 80
- Removing Memory Modules 81
- Replacing Memory Modules 81
- Removing the PCI/AGP Cage 83
- Removing the Bulkhead Screw 84
- Removing the Accessory Card 84
- Connecting the Audio Cable 85
- System Configuration menu 86
- Removing an Optical Drive 87
- Replacing an Optical Drive 88
- Removing the iLO MP Card 89
- Removing the Card 90
- Replacing the iLO MP Card 91
- Removing the LED Status Panel 92
- Removing a Processor 93
- Replacing a Processor 96
- Removing the System Board 99
- System’s Front 100
- Replacing the System Board 101
- Removing the System Battery 103
- Replacing the System Battery 103
- Power Supply Interface Module 104
- Hard Drive Backplane 106
- Troubleshooting 109
- The Diagnostic LEDs 111
- Warnings 115
- LAN LEDs 122
- System Board Diagnostic LEDs 123
- Starting HP e-DiagTools 125
- Directory of: fs1:\EFI 126
- Directory of: fs1:\EFI\BOOT 126
- EFI command 129
- SEL and FPL Log Entries 131
- System Specific Events 133
- Events Without Sensors 135
- Replacement Parts 137
- Server Accessories 149
- Selecting a Monitor 150
- NVIDIA Quadro4 980XGL 152
- Mass Storage 153
- DVD drive 154
- DVD-R (4.7 GB/3.9 GB) 155
- DVD-RAM (4.7 GB/2.6 GB) 155
- System Board 157
- Intel Itanium 2 Processor 159
- Dual Serial Controller 160
- Field Programmable Gate Array 160
- SCSI Controller 161
- IDE Interface 161
- 10/100 BT Management LAN 161
- 1 GB System LAN 161
- USB Connectors 162
- Chip Spare Functionality 162
Produits connexes et manuels pour PC/postes de travail HP Integrity rx2600
(45 pages)
(136 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels