Hp ProLiant DL320 G3 Server Manuel d'utilisateur Page 59
- Page / 119
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Server software and configuration utilities 59
To run iLO RBSU:
1. Restart or power up the server.
2. Press the F8 key when prompted during POST. The iLO RBSU runs.
3. Enter a valid iLO user ID and password with the appropriate iLO privileges
(Administer User Accounts, Configure iLO Settings). Default account
information is located on the iLO Default Network Settings tag.
4. Make and save any necessary changes to the iLO configuration.
5. Exit iLO RBSU.
HP recommends using DNS/DHCP with iLO to simplify installation. If
DNS/DHCP cannot be used, use the following procedure to disable DNS/DHCP
and to configure the IP address and the subnet mask:
1. Restart or power up the server.
2. Press the F8 key when prompted during POST. The iLO RBSU runs.
3. Enter a valid iLO user ID and password with the appropriate iLO privileges
(Administer User Accounts, Configure iLO Settings). Default account
information is located on the iLO Default Network Settings tag.
4. Select Network, DNS/DHCP, press the Enter key, and then select DHCP
Enable. Press the spacebar to turn off DHCP. Be sure that DHCP Enable is
set to Off and save the changes.
5. Select Network, NIC and TCP/IP, press the Enter key, and type the
appropriate information in the IP Address, Subnet Mask, and Gateway IP
Address fields.
6. Save the changes. The iLO system automatically resets to use the new setup
when you exit iLO RBSU.
Erase Utility
CAUTION: Perform a backup before running the System
Erase Utility. The utility sets the system to its original factory state,
deletes the current hardware configuration information, including array
setup and disk partitioning, and erases all connected hard drives
completely. Refer to the instructions for using this utility.
- User Guide 1
- Audience assumptions 2
- Contents 3
- Front panel components 7
- Front panel LEDs and buttons 8
- Rear panel components 10
- Rear panel LEDs and buttons 11
- System board components 12
- System maintenance switch 13
- System board LEDs 14
- Internal USB connector 17
- Fan module location 18
- Server operations 19
- Preparation procedures 20
- Removing the access panel 21
- Installing the access panel 22
- Server operations 23 23
- Removing the fan assembly 25
- Installing the fan assembly 26
- Server setup 27
- Rack planning resources 28
- Optimum environment 29
- Temperature requirements 30
- Power requirements 31
- Rack warnings 32
- Installing hardware options 33
- Server setup 35 35
- Registering the server 36
- Introduction 37
- Memory options 37
- DIMM installation guidelines 38
- Installing DIMMs 38
- Hard drive options 39
- Removing a hard drive blank 40
- Hard drive guidelines 40
- Installing a SATA hard drive 40
- Server cabling 47
- SATA cable routing 48
- SCSI cable routing 49
- Configuration tools 51
- HP ROM-Based Setup Utility 53
- Array Configuration Utility 54
- Management tools 56
- Automatic Server Recovery 57
- ROMPaq utility 57
- Erase Utility 59
- Management Agents 60
- HP Systems Insight Manager 60
- Redundant ROM support 61
- Diagnostic tools 63
- Array Diagnostic Utility 64
- HP Insight Diagnostics 64
- Integrated Management Log 64
- Keeping the system current 65
- Resource Paqs 66
- ProLiant Support Packs 66
- Care Pack 67
- Battery replacement 69
- 5. Remove the battery 70
- Troubleshooting 71
- Important safety information 72
- Warnings and cautions 73
- Troubleshooting 75 75
- Symptom information 76
- Service notifications 77
- Loose connections 77
- Diagnostic steps 77
- Start diagnosis flowchart 78
- Troubleshooting 79 79
- General diagnosis flowchart 80
- Troubleshooting 81 81
- Power-on problems flowchart 82
- Troubleshooting 83 83
- POST problems flowchart 85
- OS boot problems flowchart 87
- Troubleshooting 89 89
- Troubleshooting 91 91
- Other information resources 93
- Electrostatic discharge 95
- FCC rating label 98
- Class A equipment 98
- Class B equipment 99
- Modifications 100
- Mouse compliance statement 100
- Japanese notice 102
- BSMI notice 102
- Korean notice A&B 103
- Laser compliance 103
- Battery replacement notice 104
- Server specifications 107
- Specification 108
- Technical support 109
- Customer self repair 110
- Acronyms and abbreviations 111
- Wake-on LAN 115
Produits connexes et manuels pour Matériel informatique Hp ProLiant DL320 G3 Server
(28 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels