Hp ProLiant DL580 Gen8 Server Manuel d'utilisateur Page 68
- Page / 109
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Hardware options installation 68
• When returning a system board for service replacement, do not remove the TPM from the system board.
When requested, HP Service provides a TPM with the spare system board.
• Any attempt to remove an installed TPM from the system board breaks or disfigures the TPM security
rivet. Upon locating a broken or disfigured rivet on an installed TPM, administrators should consider the
system compromised and take appropriate measures to ensure the integrity of the system data.
• When using BitLocker, always retain the recovery key/password. The recovery key/password is
required to enter Recovery Mode after BitLocker detects a possible compromise of system integrity.
• HP is not liable for blocked data access caused by improper TPM use. For operating instructions, see the
encryption technology feature documentation provided by the operating system.
Retaining the recovery key/password
The recovery key/password is generated during BitLocker™ setup, and can be saved and printed after
BitLocker™ is enabled. When using BitLocker™, always retain the recovery key/password. The recovery
key/password is required to enter Recovery Mode after BitLocker™ detects a possible compromise of system
integrity.
To help ensure maximum security, observe the following guidelines when retaining the recovery
key/password:
• Always store the recovery key/password in multiple locations.
• Always store copies of the recovery key/password away from the server.
• Do not save the recovery key/password on the encrypted hard drive.
Installing the Trusted Platform Module board
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
1. Power down the server (on page 23).
2. Remove the access panel (on page 27).
3. Extend the server from the rack (on page 23).
4. Remove the SPI board (on page 30).
5. Locate the TPM connector.
CAUTION: Any attempt to remove an installed TPM from the system board breaks or disfigures
the TPM security rivet. Upon locating a broken or disfigured rivet on an installed TPM,
administrators should consider the system compromised and take appropriate measures to ensure
the integrity of the system data.
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs and buttons 7
- Systems Insight Display 8
- Rear panel components 9
- Power supply LED 10
- I/O board components 11
- System maintenance switch 12
- NMI jumper 12
- SPI board components 13
- Item Description 14
- DIMM slot locations 15
- Component identification 16 16
- DIMM fault LEDs 17
- Memory error LEDs 19
- Drive bay numbering 19
- FBWC capacitor slots 21
- FBWC module LEDs 21
- Fan locations 22
- Operations 23
- Operations 24 24
- Operations 26 26
- Remove the access panel 27
- Operations 28 28
- Remove the SPI board 30
- Rack planning resources 32
- Optimum environment 32
- Temperature requirements 33
- Rack warnings 34
- Installing hardware options 35
- Setup 36 36
- Setup 37 37
- Registering the server 38
- Introduction 39
- Processor options 39
- Installing the processor 40
- Memory cartridge option 44
- Open the DIMM slot latches 45
- Memory options 47
- DIMM identification 49
- Memory configurations 49
- Installing a DIMM 51
- SAS drive backplane option 54
- Connect the data cable 55
- SAS controller cable option 57
- Drive option 60
- 4U rack bezel option 61
- Installing the 4U rack bezel 62
- Expansion board option 63
- Install the cache module 66
- Connect the cable 66
- Cabling 71
- Server mode 72
- HP product QuickSpecs 72
- HP iLO Management 72
- Active Health System 73
- Intelligent Provisioning 74
- HP Insight Diagnostics 75
- Erase Utility 75
- HP Service Pack for ProLiant 77
- HP UEFI System Utilities 78
- Flexible boot control 79
- Secure Boot configuration 79
- Utilities and features 80
- ROMPaq utility 81
- Keeping the system current 82
- Software and firmware 83
- Version control 83
- ProLiant servers 83
- Troubleshooting 85
- Battery replacement 86
- Battery replacement 87 87
- Regulatory information 88
- Warranty information 89
- Electrostatic discharge 90
- Specifications 91
- (94% efficiency) 92
- Specifications 93 93
- Support and other resources 94
- Customer Self Repair 96
- Reparo feito pelo cliente 98
- Acronyms and abbreviations 102
- Documentation feedback 105
- Index 106 106
- Index 107 107
- Index 108 108
- Index 109 109
Produits connexes et manuels pour Matériel informatique Hp ProLiant DL580 Gen8 Server
(192 pages)
(93 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.557 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels