Hp ProLiant DL580 Gen8 Server Manuel d'utilisateur Page 78
- Page / 109
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Software and configuration utilities 78
For more information or to download SPP, see one of the following pages on the HP website:
• HP Service Pack for ProLiant download page (http://www.hp.com/go/spp)
• HP Systems and Server Software Management page (http://www.hp.com/go/SmartUpdate)
HP Smart Update Manager
HP SUM is a product used to install and update firmware, drivers, and systems software on HP ProLiant
servers. HP SUM provides a GUI and a command-line scriptable interface for deployment of systems software
for single or one-to-many HP ProLiant servers and network-based targets, such as iLOs, OAs, and VC Ethernet
and Fibre Channel modules.
For more information about HP SUM, see the product page on the HP website
(http://www.hp.com/go/hpsum).
To download HP SUM, see the HP website (http://www.hp.com/go/hpsum/download).
To access the HP Smart Update Manager User Guide, see the HP SUM Information Library
(http://www.hp.com/go/hpsum/documentation).
HP UEFI System Utilities
For servers that support UEFI, the HP UEFI System Utilities is embedded in the system ROM. The UEFI System
Utilities enable you to perform a wide range of configuration activities, including:
• Configuring system devices and installed options
• Enabling and disabling system features
• Displaying system information
• Selecting the primary boot controller
• Configuring memory options
• Selecting a language
• Launching other pre-boot environments such as the Embedded UEFI Shell and Intelligent Provisioning
For more information on the HP UEFI System Utilities, see the HP UEFI System Utilities User Guide on the HP
website (http://www.hp.com/go/uefi/docs).
Using HP UEFI System Utilities
To use the System Utilities, use the following keys:
Action Key
Access System Utilities
F9 during server POST
Navigate menus
Up and Down arrows
Select items
Enter
Save selections
F10
Access Help for a highlighted configuration option
F1
Default configuration settings are applied to the server at one of the following times:
• Upon the first system power-up
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs and buttons 7
- Systems Insight Display 8
- Rear panel components 9
- Power supply LED 10
- I/O board components 11
- System maintenance switch 12
- NMI jumper 12
- SPI board components 13
- Item Description 14
- DIMM slot locations 15
- Component identification 16 16
- DIMM fault LEDs 17
- Memory error LEDs 19
- Drive bay numbering 19
- FBWC capacitor slots 21
- FBWC module LEDs 21
- Fan locations 22
- Operations 23
- Operations 24 24
- Operations 26 26
- Remove the access panel 27
- Operations 28 28
- Remove the SPI board 30
- Rack planning resources 32
- Optimum environment 32
- Temperature requirements 33
- Rack warnings 34
- Installing hardware options 35
- Setup 36 36
- Setup 37 37
- Registering the server 38
- Introduction 39
- Processor options 39
- Installing the processor 40
- Memory cartridge option 44
- Open the DIMM slot latches 45
- Memory options 47
- DIMM identification 49
- Memory configurations 49
- Installing a DIMM 51
- SAS drive backplane option 54
- Connect the data cable 55
- SAS controller cable option 57
- Drive option 60
- 4U rack bezel option 61
- Installing the 4U rack bezel 62
- Expansion board option 63
- Install the cache module 66
- Connect the cable 66
- Cabling 71
- Server mode 72
- HP product QuickSpecs 72
- HP iLO Management 72
- Active Health System 73
- Intelligent Provisioning 74
- HP Insight Diagnostics 75
- Erase Utility 75
- HP Service Pack for ProLiant 77
- HP UEFI System Utilities 78
- Flexible boot control 79
- Secure Boot configuration 79
- Utilities and features 80
- ROMPaq utility 81
- Keeping the system current 82
- Software and firmware 83
- Version control 83
- ProLiant servers 83
- Troubleshooting 85
- Battery replacement 86
- Battery replacement 87 87
- Regulatory information 88
- Warranty information 89
- Electrostatic discharge 90
- Specifications 91
- (94% efficiency) 92
- Specifications 93 93
- Support and other resources 94
- Customer Self Repair 96
- Reparo feito pelo cliente 98
- Acronyms and abbreviations 102
- Documentation feedback 105
- Index 106 106
- Index 107 107
- Index 108 108
- Index 109 109
Produits connexes et manuels pour Matériel informatique Hp ProLiant DL580 Gen8 Server
(192 pages)
(93 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.382 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels