HP D2600 Manuel d'utilisateur Page 38
- Page / 76
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Connecting power cords
When connecting power cords, use the cords shipped with the disk enclosure.
The power cord should be approved for use in your country. The power cord must be rated for the
product and for the voltage and current marked on the electrical ratings label of the product. The
voltage and current rating for the cord should be greater than the voltage and current rating marked
on the product. In addition, the diameter of the wire must be a minimum of 1.00 mm
2
or 18 AWG,
your maximum length may be up to 3.66 m (12 ft).
After power is supplied to the disk enclosure, the power supply automatically senses the input voltage
and the power supply LED illuminates as solid amber.
To protect the system from power-failure-related downtime, each disk enclosure ships standard with
a redundant power supply. Depending how you connect the power supplies to the power source,
you can eliminate downtime caused by power-related failures.
Level of ProtectionConnection Method
Protects you from downtime when one of the disk enclosure power supplies fails.
The remaining power supply/fan module can operate the disk enclosure until you
install a replacement module.
Connected to:
• one power source
Protects you from downtime when one of the disk enclosure power supplies fails.
Protects you from data loss when one of your power sources fails, due to a pulled
cable or tripped breaker.
The remaining power source can power the disk enclosure until the failed power
source is restored or relocated. Depending on the cause and duration of the power
outage, you can use this time to properly shut down your storage sub-system.
Connected to:
• two separate power
sources
Protects you from downtime when one of the disk enclosure power supplies fails.
Protects you from data loss when one or both of your power sources fails, due to
a pulled cable, tripped breaker, or local power outage.
The remaining power source or the UPS will power the disk enclosure until power
is restored to the source. Depending on the cause and duration of the power
outage, you can use this time to properly shut down your storage sub-system.
Connected to:
• two UPS
• two separate power
sources
WARNING!
To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
• Route the power cord so that it is not likely to be walked on or pinched by items placed against
it. Pay particular attention to the plug, electrical outlet, and the point where the cord is attached
to the disk enclosure.
Installation38
- HP StorageWorks 1
- DescriptionDateEdition 2
- Contents 3
- 1 Hardware 7
- Front view 8
- Rear view 8
- Disk drives 10
- Front status and UID module 11
- Power supply module 12
- Fan module 13
- I/O module 14
- Rear power and UID module 16
- SAS cables 17
- Hardware18 18
- 2 Technical specifications 19
- Technical specifications20 20
- 3 Deployment types 21
- Deployment types22 22
- 4 Installation 23
- Preliminary tasks 24
- Striping methods 26
- RAID levels 26
- Disk drive sizes and types 27
- Spare disks 27
- Array sizing 28
- Preparing the site 29
- Racking the disk enclosure 30
- Racking procedures 31
- Disk drive options 32
- Disk drive guidelines 32
- Installing a disk drive 32
- Preparing the server 34
- Overview 35
- Cabling best practices 35
- Installation36 36
- Connecting power cords 38
- Power on best practices 39
- Power on procedures 39
- 5 Configuration 41
- Configuration42 42
- 6 Operation and management 43
- Powering off disk enclosures 44
- 7 Cabling examples 45
- 1. Host (server or controller 47
- 2. Primary disk enclosure 47
- 3. Additional cascaded disk 47
- 8 Troubleshooting 51
- Is the fan LED amber? 53
- Compromised fault tolerance 54
- Time required for a rebuild 55
- Handling disk drive failures 56
- 9 Replacement procedures 57
- Replaceable parts 58
- Replacement instructions 59
- Exploded view 59
- CSR statusDescription 60
- Contacting HP 61
- Related information 62
- Customer self repair 63
- Rack stability 63
- Support and other resources64 64
- FCC rating label 65
- European Union notice 66
- Japanese notices 66
- Korean notices 67
- Taiwanese notices 67
- Recycling notices 67
- Bulgarian notice 68
- Czech notice 68
- Danish notice 68
- Dutch notice 68
- Estonian notice 69
- Finnish notice 69
- French notice 69
- German notice 69
- Greek notice 70
- Hungarian notice 70
- Italian notice 70
- Latvian notice 70
- Lithuanian notice 71
- Polish notice 71
- Portuguese notice 71
- Romanian notice 71
- Slovak notice 72
- Spanish notice 72
- Swedish notice 72
- Turkish notice 72
Produits connexes et manuels pour Réseaux de disques HP D2600
(53 pages)
(60 pages)
Réseaux de disques HP AJ758A Fiche technique
(48 pages)
(48 pages)
Réseaux de disques HP AX670A Fiche technique
(19 pages)
(19 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.266 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels