Thermal Specifications and Design Considerations

80 Dual-Core Intel® Xeon® Processor 3000 Series Datasheet

5.1.2 Thermal Metrology

The maximum and minimum case temperatures (T

) for the processor is specified in

Table 5-1. This temperature specification is meant to help ensure proper operation of

the processor. Figure 5-4 illustrates where Intel recommends T

thermal

measurements should be made. For detailed guidelines on temperature measurement

methodology, refer to the Dual-Core Intel

Xeon

Processor 3000 Series Thermal and

Mechanical Design Guidelines.

5.2 Processor Thermal Features

5.2.1 Thermal Monitor

The Thermal Monitor feature helps control the processor temperature by activating the

thermal control circuit (TCC) when the processor silicon reaches its maximum operating

temperature. The TCC reduces processor power consumption by modulating (starting

and stopping) the internal processor core clocks. The Thermal Monitor feature must

be enabled for the processor to be operating within specifications. The

temperature at which Thermal Monitor activates the thermal control circuit is not user

configurable and is not software visible. Bus traffic is snooped in the normal manner,

and interrupt requests are latched (and serviced during the time that the clocks are on)

while the TCC is active.

When the Thermal Monitor feature is enabled, and a high temperature situation exists

(i.e., TCC is active), the clocks will be modulated by alternately turning the clocks off

and on at a duty cycle specific to the processor (typically 30–50%). Clocks often will

not be off for more than 3.0 microseconds when the TCC is active. Cycle times are

processor speed dependent and will decrease as processor core frequencies increase. A

small amount of hysteresis has been included to prevent rapid active/inactive

transitions of the TCC when the processor temperature is near its maximum operating

temperature. Once the temperature has dropped below the maximum operating

temperature, and the hysteresis timer has expired, the TCC goes inactive and clock

modulation ceases.

Figure 5-4. Case Temperature (T

) Measurement Location

37.5 mm

Measure T

at this point

(geometric center of the package)

37.5 mm

Measure T

at this point

(geometric center of the package)

37.5 mm

1 2 ... 73 74 75 76 77 78 79 80 81 82 83 ... 101 102

Commentaires sur ces manuels

Pas de commentaire

MULTIQUIP MQ Power Whisperwatt 60HZ Generator DCA150USJ2 podręczniki

Instrukcje obsługi i podręczniki użytkownika dla Do samochodu MULTIQUIP MQ Power Whisperwatt 60HZ Generator DCA150USJ2.
Dostarczamy 1 pdf podręczników MULTIQUIP MQ Power Whisperwatt 60HZ Generator DCA150USJ2 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika

Modele	Rodzaj dokumentu
Control Box Replacement LS60TD	Instrukcja Użytkownika Multiquip Control Box Replacement LS60TD User Manual, 8 strony
Trash Pump QP3TY	Instrukcja Użytkownika Multiquip Trash Pump QP3TY User Manual, 56 strony
60HZ GENERATOR DCA25SSIU3	Instrukcja Użytkownika Multiquip 60HZ GENERATOR DCA25SSIU3 User Manual, 76 strony
Tamping Rammer Mikasa MT-86D	Instrukcja Użytkownika Multiquip Tamping Rammer Mikasa MT-86D User Manual, 50 strony

HP AT80613003543AF Fiche technique Page 78

Commentaires sur ces manuels

MULTIQUIP MQ Power Whisperwatt 60HZ Generator DCA150USJ2 podręczniki

Multiquip MQ Power Whisperwatt 60HZ Generator DCA150USJ2 Instrukcja Użytkownika (102 strony)

Spis treści

Więcej produktów i instrukcji dla Do samochodu MULTIQUIP

HP AT80613003543AF Fiche technique Page 78

Commentaires sur ces manuels

Produits connexes et manuels pour Processeurs HP AT80613003543AF

MULTIQUIP MQ Power Whisperwatt 60HZ Generator DCA150USJ2 podręczniki

Multiquip MQ Power Whisperwatt 60HZ Generator DCA150USJ2 Instrukcja Użytkownika (102 strony)

Spis treści

Więcej produktów i instrukcji dla Do samochodu MULTIQUIP