HP ProLiant Smart Array E200 Guide de l'utilisateur Page 30
- Page / 118
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Setup 30
Item Description
10 Serial connector
11 USB connector
12 USB connector
13 iLO 2 NIC connector
3. Use the strain relief clip from the server hardware kit to secure the power cord.
Powering up and configuring the server
To power up the server, press the Power On/Standby button.
While the server boots, RBSU and the ORCA utility are automatically configured to prepare the server for
operating system installation.
To configure these utilities manually:
• Press the F8 key when prompted during the array controller initialization to configure the array
controller using ORCA.
• Press the F9 key when prompted during the boot process to change the server settings using RBSU.
The system is set up by default for the English language.
For more information on the automatic configuration, refer to the HP ROM-Based Setup Utility User Guide
located on the Documentation CD.
Installing the operating system
To operate properly, the server must have a supported operating system. For the latest information on
supported operating systems, refer to the HP website (http://www.hp.com/go/supportos
).
Two methods are available to install an operating system on the server:
• SmartStart assisted installation—Insert the SmartStart CD into the CD-ROM drive and reboot the
server.
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Rear panel components 9
- Rear panel LEDs and buttons 10
- System board components 11
- System maintenance switch 12
- NMI switch 12
- SAS and SATA device numbers 15
- SAS and SATA hard drive LEDs 16
- Fan locations 17
- Operations 18
- Remove the access panel 20
- Install the access panel 20
- Operations 24 24
- In this section 25
- Rack planning resources 26
- Optimum environment 26
- Temperature requirements 27
- Power requirements 27
- Rack warnings 28
- Installing hardware options 28
- Registering the server 31
- Introduction 32
- Processor option 32
- Memory options 37
- Advanced ECC memory 38
- Installing FBDIMMs 40
- Removing hard drive blanks 41
- Multibay device options 43
- Expansion board options 46
- P400i Controller 50
- Cabling 63
- Cabling 64 64
- Battery pack cabling 65
- Multibay backplane cabling 66
- Configuration and utilities 67
- HP ROM-Based Setup Utility 68
- Boot options 69
- BIOS Serial Console 69
- Configuring mirrored memory 69
- Array Configuration Utility 70
- Management tools 71
- Erase Utility 72
- Management Agents 73
- HP Systems Insight Manager 73
- Redundant ROM support 73
- Diagnostic tools 74
- Array Diagnostic Utility 75
- HP Insight Diagnostics 75
- Integrated Management Log 75
- Keeping the system current 76
- Care Pack 78
- Troubleshooting 79
- Symbols on equipment 80
- Warnings and cautions 80
- Symptom information 81
- Loose connections 82
- Service notifications 82
- Troubleshooting flowcharts 83
- General diagnosis flowchart 84
- Symptoms: 86
- Troubleshooting 88 88
- POST problems flowchart 89
- OS boot problems flowchart 90
- Troubleshooting 92 92
- Possible causes: 93
- Redundancy failure 93
- Troubleshooting 94 94
- System battery 95
- FCC rating label 96
- FCC logo, United States only 97
- Modifications 98
- Japanese notice 99
- BSMI notice 99
- Korean notice 100
- Laser compliance 100
- Battery replacement notice 100
- Electrostatic discharge 102
- Specifications 103
- Technical support 105
- Technical support 106 106
- Customer Self Repair 107
- Reparo feito pelo cliente 109
- Technical support 110 110
- Technical support 111 111
- Technical support 112 112
- Acronyms and abbreviations 113
- Index 116 116
- Index 117 117
- Index 118 118
Produits connexes et manuels pour Serveurs HP ProLiant Smart Array E200
Serveurs HP ProLiant DL585 G2 Spécifications
(106 pages)
(106 pages)
Serveurs HP Proliant DL580 Spécifications
(97 pages)
(97 pages)
Serveurs HP BL680c G5 Guide de l'utilisateur
(100 pages)
(100 pages)
Serveurs HP DL380z Guide de l'utilisateur
(133 pages)
(133 pages)
Serveurs HP HP ProLiant DL385 Spécifications
(106 pages)
(106 pages)
Serveurs HP ML150 - ProLiant - G6 Spécifications
(114 pages)
(114 pages)
Serveurs HP Z200 Spécifications
(192 pages)
(192 pages)
Serveurs HP Server tc3100 Spécifications
(111 pages)
(111 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels