HP LaserJet 4100 Manuel de service Page 79
- Page / 336
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
EN Chapter 3 Printer operation 77
Page count
The page count that is stored in nonvolatile memory (NVRAM) and is shown on the configuration
page printout represents the number of pages the printer has printed (excluding engine test prints). If
it is necessary to install a new formatter in the printer, the page count must be reset so that it
represents the age of the printer engine rather than the age of the formatter.
Note Before replacing the formatter or firmware DIMM, print a configuration page and a menu map to verify
the current printer settings. Use the information on these pages to reset the customer’s printer settings.
Maintenance count
The maintenance count should be reset only after a maintenance kit has been installed. For more
information, see page 86.
Maintenance interval
The
MAINTENANCE INTERVAL
in the service-mode menu sets the page count interval at which the next
service is due for the printer. This is set initially at the factory to 200,000 pages. (For example, the
PERFORM PRINTER MAINTENANCE
message appears at 200,000 pages. If the printer maintenance kit is
installed at 200,114 pages, the message reappears 200,000 pages later, at 400,114 pages.) The
procedure for editing this number is similar to editing the
PAGES
item.
Serial number
The printer serial number is stored in NVRAM. If a formatter is replaced, then the printer serial
number must be reentered. The procedure for editing this number is similar to editing the
PAGES
item.
Note Before replacing the formatter or firmware DIMM, print a configuration page and a menu map to verify
the current printer settings. Use the information on these pages to reset the customer’s printer settings.
Cold reset paper
The cold reset paper size is stored in NVRAM. When a printer cold reset is performed, the default
paper size (in the printing menu) is set to the value saved for the cold reset paper size. Possible
values are
COLD RESET PAPER=LETTER
and
COLD RESET PAPER=A4
. When replacing the formatter in
countries that use A4 rather than letter-size paper, set the cold reset paper size to
A4
.
Diagnostics
This menu item enables or disables the use of the firmware diagnostic features for software
development. Possible values are
DIAGNOSTICS=OFF*
and
DIAGNOSTICS=ON
. When enabled, the
diagnostic features are available when the printer is in the online
READY
state by pressing the S
ELECT
key.
Note The feature above is for software developers only.
- Service Manual _____________ 3
- Contents 5
- 4 Printer maintenance 6
- 5 Theory of operation 6
- 7 Troubleshooting 8
- 8 Parts and diagrams 8
- 10 Figures EN 12
- Printer description 15
- Printer features 16
- Product compatibility matrix 20
- Identification 22
- Site requirements 23
- Installation requirements 24
- Environmental requirements 26
- Print media specifications 27
- Types of print media to avoid 31
- Weight equivalence table 32
- Adhesive labels 33
- Overhead transparencies 34
- Envelopes 35
- Envelope specifications 36
- Card stock and heavy paper 37
- Safety information 38
- Laser safety 39
- Regulatory information 39
- 38 Printer description EN 40
- Service approach 41
- Parts and supplies 42
- Printer documentation 43
- Exchange program 44
- Consumables 44
- World Wide Web 44
- Toner cartridge information 46
- Warranty statement 47
- 46 Service approach EN 48
- Printer operation 49
- 48 Printer operation EN 50
- Using the control panel 51
- Control panel keys 52
- Settings and defaults 53
- Control panel menus 54
- Quick copy jobs menu 55
- Private/stored jobs menu 56
- Information menu 57
- Paper-handling menu 59
- Printing menu 62
- Print quality menu 65
- Configuration menu 68
- I/O menu 71
- EIO menu (networked printers) 72
- Resets menu 75
- Service mode 76
- Service menu 77
- Testing the printer 80
- Resetting the printer 81
- System configuration 82
- Printer maintenance 83
- Using the auto-cleaning page 86
- Cleaning spilled toner 87
- PERFORM PRINTER MAINTENANCE 88
- Expected life of components 89
- 88 Printer maintenance EN 90
- Theory of operation 91
- Power supply system 93
- Toner-cartridge detection 96
- Engine controller system 97
- 96 Theory of operation EN 98
- 98 Theory of operation EN 100
- 100 Theory of operation EN 102
- Laser/scanner drive 103
- Engine test print 103
- 102 Theory of operation EN 104
- Figure 17. Main motor control 104
- Formatter system 106
- EconoMode 107
- Input/output 107
- Printer memory 108
- DIMM slots 108
- PJL overview 109
- Control panel 109
- Image formation system 110
- Toner cartridge 111
- Photosensitive 112
- Aluminum 112
- Conditioning the drum 113
- Writing the image 114
- Developing the image 115
- Transferring the image 116
- Variable fusing temperature 118
- Paper feed system 119
- 118 Theory of operation EN 120
- Figure 29. Paper path 121
- Clutches and sensors 122
- Printing from tray 1 122
- Printing from tray 2 124
- Pickup and feeding 127
- 126 Theory of operation EN 128
- Figure 36. Paper feed pickup 128
- Envelope feeder 129
- Duplexer 129
- Other controls 131
- Basic sequence of operation 132
- Figure 38. Timing diagram 133
- 132 Theory of operation EN 134
- Removing and replacing parts 135
- Required tools 138
- Removing covers 140
- Control panel board 142
- Top cover 143
- Left side cover 145
- Front right side cover 146
- Rear cover/rear output bin 147
- Removing internal assemblies 151
- Firmware DIMM 152
- Formatter assembly 153
- Output delivery assembly 154
- Laser/scanner 156
- Cartridge memory 157
- Main motor 160
- Transfer roller 161
- Tray 1 pickup roller 162
- Tray 1 pickup assembly 163
- Registration assembly 167
- Paper feed assembly 169
- Delivery drive assembly 172
- Engine controller board 175
- Adjusting the top margin 177
- Paper-feed guide assembly 178
- Removing tray assemblies 179
- Troubleshooting 185
- Troubleshooting process 186
- Troubleshooting flowchart 187
- 186 Troubleshooting EN 188
- Preliminary operating checks 189
- Power on 190
- Engine test 192
- Event log 193
- Print the event log 194
- Display the event log 194
- Interpret the event log 194
- Printer messages 195
- Information pages 224
- Embedded Web server 226
- Embedded Web server page sets 226
- Home page set 227
- Configuration page 228
- Image quality 229
- Check the toner cartridge 230
- Image defects 232
- Repetitive defect ruler 245
- Image system troubleshooting 246
- Reference diagrams 248
- 248 Troubleshooting EN 250
- 250 Troubleshooting EN 252
- Paper path 254
- Motors and fans 259
- Connectors 260
- 260 Troubleshooting EN 262
- Figure 112. Location of PCAs 263
- Solenoids and clutch 268
- 268 Troubleshooting EN 270
- Parts and diagrams 271
- Ordering parts 272
- Ordering consumables 272
- Accessories and supplies 273
- Illustrations and parts lists 276
- Firmware DIMM kit 278
- 278 Parts and diagrams EN 280
- 280 Parts and diagrams EN 282
- 282 Parts and diagrams EN 284
- 284 Parts and diagrams EN 286
- 286 Parts and diagrams EN 288
- 292 Parts and diagrams EN 294
- 298 Parts and diagrams EN 300
- 300 Parts and diagrams EN 302
- 304 Parts and diagrams EN 306
- Alphabetical parts list 308
- Numerical parts list 315
- 320 Parts and diagrams EN 322
- EN Index 321 323
- Numerics 323
- 322 Index EN 324
- EN Index 323 325
- 324 Index EN 326
- EN Index 325 327
- 326 Index EN 328
- EN Index 327 329
- 328 Index EN 330
- EN Index 329 331
- 330 Index EN 332
- EN Index 331 333
- 332 Index EN 334
- *C8049 * 336
- *C * 336
- 8049-90920 336
Produits connexes et manuels pour Imprimantes laser/LED HP LaserJet 4100
(730 pages)
(256 pages)
(101 pages)
(82 pages)
(60 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.388 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels