Hp StorageWorks XP10000 Disk Array Manuel d'utilisateur Page 130
- Page / 220
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
• Whether or not the user information for the host that attempts to connect is registered on the
iSCSI target
Table 20 shows the relationship between combinations of iSCSI target settings and connection results in
authentication of hosts. Regardless of whether or not the host is configured for authentication by ports
with CHAP, the connection results are as follows, unless otherwise noted.
Table 20 Combinations of port settings and connection results (iSCSI environments)
Port settings
Authentication:
at target
Host user
information
Host settings
Connection results
Enable Registered Registered
Connected if the authentication of
the host succeeded
1
Enable Registered Not registered Failed to be authenticated and
cannot be connected
Enable Not registered Registered Failed to be authenticated and
cannot be connected
Disable
—
2
—
2
Connected without authentication of
the host
3
1
If a host is not configured for authentication by ports with CHAP, the host cannot connect to the array.
2
This item does not affect the connection results, or cannot be specified.
3
If a host uses Microsoft iSCSI Initiator and is configured for authentication by ports with CHAP, authentication of the host fails.
To allow such a host to connect to the port without authentication, do not configure it for authentication by ports with CHAP.
For more information about authentication of hosts, see User authentication (iSCSI environments).
Operating NAS channel adapters
You can use LUN Manager to check the running status of OSs on NAS channel adapters. Also, when a
failure occurs on the OS, you can operate (restart, stop, or start) the OS using LUN Manager without
going to the array's cabinet.
NOTE:
You cannot perform operations related to NAS channel adapters and set Fibre Channel ports at the same
time. Therefore, if you change a Fibre Channel port setting first in the Port pane, you cannot operate
the NAS channel adapter. Click Apply once to apply the change to the array, and then operate the
NAS channel adapter's OS.
Restarting a NAS channel adapter's OS
1. Start LUN Manager, and display the Port pane (Figure 23).
2. In the Package tree, select the NAS folder or a NAS channel adapter.
•IfyouselecttheNAS folder, the CHN list displays the NAS channel adapters in the array.
• If you select a channel adapter, the CHN list displays information about that channel adapter.
3. In the CHN list, select the channel adapter whose OS Status column contains UP.TheReboot and
Shut Down buttons are activated.
4. Click Reboot.Aconfirmation message appears.
5. Click OK. The row selected in the CHN list appears in blue and the operation (Reboot) appears in the
Setting column. Also, the channel adapter name to be operated appears in blue in the Package tree.
6. Click Apply.Aconfirmation message appears.
7. Click OK. The selected NAS channel adapter's OS restarts.
13 0
LUN Manager operations
- XP12000/XP10000/SVS200 1
- LUN Manager an 1
- Contents 3
- About this guide 13
- Document conven 14
- HP technical support 14
- Subscription s 15
- HP websites 15
- Documentation feedback 15
- 1 Overview of LUN Manager 17
- Configuring LU paths 18
- Configuring LU p 19
- Overview of LUN Manager 20
- Configuring LUN security 24
- Fibre Channel ports 26
- Fibre Channel port addresses 27
- Fibre PCB modes 31
- Ahyphen( 38
- NS server settings 44
- Microsoft® iSNS Server 45
- Authenti 50
- NAS channel adapters 55
- System requirements 57
- Enabling required software 57
- Notes on using LUN Manager 57
- Preparing to use LUN Manager 58
- 3LUNManagerpanes 59
- LU Path tree 60
- NAS folder 61
- LUN Manager panes 62
- LU Path table 63
- Lower-left list 64
- LDEV table 65
- Port pane 67
- Package tree 68
- Port table 69
- Change Port Mode box 71
- CHN list 73
- Authentication pane 74
- Fibre folder 76
- Port Information list 77
- FC Switch Information list 77
- 4LUNManageroperations 79
- Creating host gr 80
- Disk Arrays 87
- HP StorageWorks 90
- Deleting LU paths 91
- Changing a host 93
- 94 LUN Manager operations 94
- Deleting host groups 95
- Deleting iSCSI targets 96
- Initializing iS 97
- CSI target 0 (zero) 97
- LUN Manager operations 100
- Deleting unneed 101
- 104 LUN Manager operations 104
- Using LUN security 105
- Enabling LUN security 106
- Disabling LUN security 106
- Configuring arr 107
- 114 LUN Manager operations 114
- Setting user au 115
- Settings an 120
- Specifying whe 124
- 5TroubleshootingLUNManager 133
- WorldWideName(WWN) 135
- 7OverviewofVolumeManager 139
- Volume Manager guidelines 140
- HP StorageWorks LUN 141
- CVS function 142
- Parity group configuration 143
- Volume to Space function 144
- Install CV fun 145
- Volume In 152
- SSID requirements 153
- Requirements for CU groups 154
- 8PreparingtouseVolume 155
- Manager or Custom Volume Size 155
- Changing to Modify mode 156
- 9 Volume Manager operations 159
- LDEV Information table 160
- Capacity Unit box 161
- Selected LDEVs 161
- Select an LDEV list 161
- Volume Count list 161
- Free LDEVs table 161
- Expanded LDEVs list 162
- Set LUSE Confi rmation pane 163
- Release LUSE Confirmation pane 164
- Reset LUSE Confirmation pane 165
- Concatenation List pane 165
- Volume Manager operations 166
- Creating LUSE volumes 167
- Releasing LUSE volumes 170
- Changing LUSE capacities 170
- 3. Click OK 171
- Custom Volume 173
- Size panes 173
- Capacity Unit list 174
- Parity Group - LDEV table 174
- Progress bar 176
- Install CV pane (1) 177
- Custom Volume Size operations 178
- Install CV pane ( 181
- Install CV pane (3) 183
- Install CV pane (4) 184
- Make Volume pane 185
- Make Volume pane (2) 189
- Make Volume pane (3) 191
- Make Volume pane (4) 192
- Volume Initialize pane (1) 193
- Volume Initialize pane (2) 195
- Volume Initialize pane (3) 196
- Concatenation L 198
- Format A 198
- Write to Control Blocks pane 199
- CVS operations 200
- Deleting CVS vo 205
- Formatting LDEVs 209
- 11 Troubleshooting Volume 213
Produits connexes et manuels pour Stockage Hp StorageWorks XP10000 Disk Array
Stockage Hp XP7 Storage Manuel d'utilisateur
(53 pages)
(53 pages)
Stockage Hp XP7 Storage Manuel d'utilisateur
(27 pages)
(27 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels