HP 132A Manuel d'utilisateur Page 303
- Page / 330
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 4 Command Reference
Introduction
Programming Guide 4-137
*RST
(Reset Command)
*RST
This event command performs an instrument reset .
The reset performs the following:
• sets instrument settings to their *RST states,
• disables macros,
• places instrument in “Operation Complete Idle State” and “Operation
Complete Query Idle State,” and
• clears (empties) the Key Queue
The reset does not affect:
• the macros defined with *DMC,
• the calibration data,
• the Service Register Enable or the Standard Event Status Enable,
• the Output Queue, and
• the IEEE 488.1 address or the state of the IEEE 488.1 interface.
See the section titled “*RST Response,” page 2-36, in Chapter 2 of this guide for
a complete listing of the *RST state.
Each command description in this chapter (Chapter 4) includes the *RST state in
the “Comment” portion of the definition.
- HP 53131A/132A 225 MHz 1
- Universal Counter 1
- Programming Guide 3
- Contents 5
- Operation 6
- 4 Command Reference 10
- 5 Errors 12
- Before You Start 13
- Introduction 14
- Calibrations 15
- Statistics 16
- HP-IB Commands 16
- Getting Started 18
- How to Use This Guide 18
- Experienced Programmers 19
- Applications 20
- Programming Guide Contents 21
- Assumptions 21
- Related Documentation 22
- 1-12 Programming Guide 24
- Command Summary 25
- Some SCPI Syntax Conventions 27
- Channel 3 is optional 28
- SCPI Command Map 30
- Chapter 2 Command Summary 32
- 2-8 Programming Guide 32
- 2-10 Programming Guide 34
- Programming Guide 2-13 37
- 2-14 Programming Guide 38
- Programming Guide 2-15 39
- 2-16 Programming Guide 40
- (Part 1 of 2) 40
- 2-18 Programming Guide 42
- SCPI Conformance Information 44
- IEEE 488.2 Common Commands 45
- 2-22 Programming Guide 46
- Programming Guide 2-23 47
- Std/New Column 48
- Parameter Form Column 48
- Programming Guide 2-25 49
- 2-26 Programming Guide 50
- Programming Guide 2-27 51
- 2-28 Programming Guide 52
- Programming Guide 2-29 53
- 2-32 Programming Guide 56
- Programming Guide 2-33 57
- 2-34 Programming Guide 58
- Programming Guide 2-35 59
- 2-36 Programming Guide 60
- Programming Guide 2-37 61
- 2-38 Programming Guide 62
- Arming SCPI Command Summary 62
- Programming Guide 2-39 63
- *RST Response 64
- sensitivity 65
- hysteresis 65
- 2-44 Programming Guide 68
- Remote Operation 69
- Configuring the HP-IB 72
- Remote/Local Operation 74
- Common Command Format 75
- SCPI Command and Query Format 75
- Abbreviated Commands 77
- Keyword Separator 77
- Optional Keyword 77
- Parameter Types 79
- Parameter Separator 80
- Query Parameters 80
- Suffixes 80
- Command Terminator 81
- Using Multiple Commands 82
- Response Messages 84
- Response Message Syntax 84
- Response Message Data Types 85
- 3-18 Programming Guide 86
- Status Reporting 87
- 3-20 Programming Guide 88
- Functional Diagram 88
- Status Byte Register 89
- Status Register Group 95
- Condition Register 96
- Transition Filter 96
- Event Register 97
- Event Enable Register 97
- Reporting 106
- HP-IB command—Example 2 107
- Disabled—Example 3 107
- Measuring has Completed— 108
- Example 4 108
- Programming Guide 3-41 109
- Elements of SCPI Commands 109
- 3-42 Programming Guide 110
- Measurements 114
- Using the *OPC? Command 115
- Operations 117
- Writing SCPI Programs 123
- 3-56 Programming Guide 124
- Programming Guide 3-57 125
- Programming Examples 126
- Using QuickBASIC 127
- Using Turbo C 127
- 3-60 Programming Guide 128
- Programming Guide 3-61 129
- 3-62 Programming Guide 130
- Programming Guide 3-63 131
- (HP BASIC) 132
- (HP BASIC) (Continued) 133
- 3-66 Programming Guide 134
- BASIC) (Continued) 135
- (Continued) 138
- Programming Guide 3-73 141
- 3-74 Programming Guide 142
- To Use Macros (HP BASIC) 143
- 3-76 Programming Guide 144
- Programming Guide 3-77 145
- 3-78 Programming Guide 146
- Programming Guide 3-79 147
- 3-80 Programming Guide 148
- (QuickBASIC) 150
- (QuickBASIC) (Continued) 151
- Programming Guide 3-85 153
- 3-86 Programming Guide 154
- Programming Guide 3-87 155
- To Use Macros (QuickBASIC) 156
- Programming Guide 3-89 157
- 3-90 Programming Guide 158
- Programming Guide 3-91 159
- 3-92 Programming Guide 160
- Programming Guide 3-93 161
- C) (Continued) 162
- 3-96 Programming Guide 164
- Programming Guide 3-97 165
- 3-98 Programming Guide 166
- Command Reference 167
- :ABORt Command 170
- :CALCulate Subsystems 171
- Chapter 4 Command Reference 172
- 4-6 Programming Guide 172
- :CALCulate[1] Subsystem 173
- :CALCulate[1]:IMMediate 174
- :CALCulate[1]:MATH Subtree 175
- :CALCulate2 Subsystem 177
- :CALCulate2:LIMit Subtree 178
- Query Response 179
- Comments 179
- :CALCulate2:LIMit:FAIL? 180
- [HZ 182
- [HZ 184
- :CALCulate3 Subsystem 185
- :CALCulate3:AVERage:CLEar 186
- 188
- :CALCulate3:DATA? 188
- :CALCulate3:LFILter Subtree 189
- :CALCulate3:PATH? 191
- :CALibration Subsystem 192
- Front-Panel 193
- :CALibration:SECurity Subtree 194
- :CONFigure Subsystem 196
- Device Clear 197
- :DIAGnostic Subsystem 198
- AUTO ONCE 199
- :DISPlay Subsystem 203
- “[:]CALCulate3” 204
- :FETCh Subsystem 206
- :FORMat Subsystem 207
- Group Execute Trigger 208
- :HCOPy Subsystem 209
- :INITiate Subsystem 210
- :INITiate[:IMMediate] 212
- :INPut[1 214
- :INPut3 Subsystem 216
- :MEASure Subsystem 217
- :FETCh, :MEASure, :READ) 218
- [,<source_list>] 219
- :CONFigure? 220
- 4-64 Programming Guide 230
- Programming Guide 4-69 235
- 4-72 Programming Guide 238
- Using :MEAsure 241
- Using :CONFigure with :READ? 242
- :MEMory Subsystem 245
- [:SENSe] Subsystem 246
- <numeric_value> [V] 248
- <numeric_value> [PCT] 249
- [:SENSe]:EVENt3 Subtree 250
- [:SENSe]:EVENt3:SLOPe? 251
- [:SENSe]:FREQuency Subtree 251
- 252
- 253
- <numeric_value> [S] 253
- <numeric_value> [HZ] 254
- [:SENSe]:PHASe Subtree 257
- [:SENSe]:ROSCillator Subtree 258
- S/N Prefix Below 3646) 261
- (HP 53131A and HP 53132A 261
- With S/N Prefix Below 3646) 261
- Programming Guide 4-99 265
- 269
- [:SENSe]:TOTalize Subtree 270
- EXTernal TIMer 272
- :STATus Subsystem 273
- :STATus:OPERation[:EVENt]? 274
- :STATus:OPERation:NTRansition 275
- :STATus:OPERation:PTRansition 275
- :STATus:PRESet 276
- :STATus:QUEStionable Subtree 276
- :STATus:QUEStionable[:EVENt]? 278
- :SYSTem Subsystem 280
- <numeric_value> 281
- ODD 282
- :SYSTem:ERRor? 282
- :SYSTem:KEY:LOG? 284
- :SYSTem:VERSion? 284
- :TRACe Subsystem 285
- :TRACe[:DATA]? SCALE 286
- :TRIGger Subsystem 287
- (Calibration Query) 288
- (Clear Status Command) 289
- *DDT <arbitrary block> 290
- (Define Macro Command) 291
- *EMC <NRf> 292
- (Enable Macro Command) 292
- (Enable Macro Query) 292
- *ESE <NRf> 293
- (Event Status Register Query) 294
- *GMC? <string> 295
- (Get Macro Contents Query) 295
- (Identification Query) 296
- (Learn Macro Query) 297
- (Operation Complete Command) 298
- (Operation Complete Query) 299
- (Option Identification Query) 300
- (Purge Macro Command) 301
- *RCL <NRf> 302
- (Recall Command) 302
- (Reset Command) 303
- *SAV <NRf> 304
- (Save Command) 304
- *SRE <NRf> 305
- (Status Byte Query) 306
- (Trigger Command) 307
- (Self-Test Query) 308
- (Wait-to-Continue Command) 309
- 4-144 Programming Guide 310
- Displaying Errors 312
- Reading an Error 312
- Error Queue 313
- Error Types 314
- Execution Error 315
- Query Error 316
- Chapter 5 Errors 317
- Programming Guide 5-7 317
- Table 5-2. Errors 317
- 5-8 Programming Guide 318
- Programming Guide 5-9 319
- 5-10 Programming Guide 320
- Programming Guide Index-1 321
- Index-4 Programming Guide 324
- Programming Guide Index-5 325
- Technical Support: 327
Produits connexes et manuels pour Mesure, test et contrôle HP 132A
(112 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels