HP EVA3000 Manuel d'utilisateur Page 96
- Page / 165
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
NOTE:
Because this component is used in severa l products, the drawings may reflect a differ ent enclosure than
theoneyouhave.Theremovalandreplacementprocedureisthesameforeachproduct.
Before you begin
Observe the following precautions when replacing the power supply/blower.
CAUTION:
You have only seven minutes to perform t h e replacement procedure! Both power supplies must be
installed for the enclosure to cool properly. If a power supply fails, leave it in place in the enclosure until
a new power supply is available to install. The enclosure could shut down d ue to overheating unless the
power supply is replaced within seven minutes of removal of the failed/failing power supply.
If cabling is obstructing access to the power supply/blower, carefully move the cables out of the way
to avoid loosening any connections.
Parts can be damaged by electrostatic discharge. Use proper anti-static protection. Refer to the
documentation that shipped with your system for additional information.
Have a copy of the product User Guide available for reference. You can download a copy of the User
Guide from the product support page on the HP website.
Verifying component failure
CAUTION:
If HP Command View EVA does not present a status consistent with the power supply/blower status
indicator
, or if HP Command View or your system monitoring tool indicates multiple hardware failures,
contact HP
support for assistance (h
ttp://www.hp.com/support).
The power supply and blower are separately replaceable components. Before replacing a power supply
or blower, use the following m etho d s to verify the component failure:
• Analyzeanyfailuremessagesyoumayhavereceivedfromsystemmonitoring(SystemEvent
Analyzer).
• Check status using HP Command View EVA:
1. In the Navigation pane, select Storage system > Hardware > Rack > Disk enclosure.
2. In the Content pane, select the Power tab or the Cooling tab then the appropriate component (1
or 2). The Operational state should be
Failed.
3. To help identify the correct enclosure, click Locate > Locate On to flash the status indicators
on the front of the disk enclosure.
• Check the power supply/blower status indicator. See Figure 41.Itshouldbeoff.
96
Customer replaceable units
- Part number: 5697-7026 1
- Contents 3
- About this guide 13
- Rack stability 14
- HP technical support 14
- Customer self repair 15
- Product warranties 15
- Subscription service 15
- HP websites 15
- Documentation feedback 15
- 1 Enterprise Virtu al Array 17
- Performance 18
- Scalability 18
- Operating system support 18
- Storage system components 19
- Controller soft ware 20
- Hardware 20
- Fibre Channel drive enclosure 21
- Fibre Channel lo 22
- HSV110 and HSV100 controllers 22
- P = Fibre (Host) Port 26
- CA = Fibre Channel Adapter 26
- Gathering information 27
- Host information 28
- Entering the WW 29
- Entering the WWN checksum 29
- Installing opti 31
- 3 Enterprise Virtu al Array 33
- Setting Point in time 34
- Behavior 34
- Storage s ystem s 37
- Creating disk groups 40
- Adding a disk driv e 41
- Changing the De 42
- Installing the disk drive 42
- Checking status indicators 42
- Handling fiber optic cables 43
- 4 Enterprise Virtu al Array 45
- I/O m odules 46
- I/O module status indicators 47
- Fi bre Optic Fibr 49
- Copper Fibre Channel cables 49
- Fibre Channel disk drives 49
- Disk drive stat 50
- Disk drive status displays 50
- Power supplies and blowers 51
- Power supplies 52
- Drive enclosure EMU 53
- EMU functions 54
- EMU monitoring functions 55
- EMU displays 55
- EMU indicator di 56
- Audible alarm operations 57
- Enabling the audible alarm 58
- Muting or unmut 59
- Disabling the audible alarm 59
- Enclosure numb 60
- Error Condition Reporting 62
- Reporting group feature 65
- Fibre Channel loop switches 66
- Power-on self test (POST) 67
- Reading the switch indicators 67
- HSV controllers 69
- High availability features 70
- Operator control panel 70
- Status indicators 71
- Navigation butt 72
- Alphanumeric display 72
- Displaying the OCP menu tree 72
- Displaying system information 73
- Shutting down the system 74
- Shutting the controller down 74
- Restarting the system 75
- Uninitializing the system 75
- Password options 75
- Changing a password 75
- Clearing a password 76
- Cache bat tery 77
- HSV controller cabling 77
- Rack configurations 77
- Power d istribution 77
- Rack AC po 80
- Moving and stabilizing a rack 82
- 1. H ex n ut 83
- 2. Leveler foot 83
- Customer self 85
- Replaceable parts 86
- Before you begin 88
- Types of disk failures 89
- Checking system re dundancy 89
- Verifying component failure 90
- 1. Ac t ivi t y 92
- 2. Online 3. Fault 92
- Removing a di 93
- Installing a disk 94
- Verifyin 94
- Removing a b 97
- Installing a blower 97
- Removing a po 98
- Installing a p ower supply 98
- Verifying proper operation 99
- Customer replaceable units 100
- A Regulatory notices an d 101
- Laser device 102
- European union notice 103
- Notice for Fra 104
- WEEE Recycling Notices 104
- French notice 105
- German notice 105
- Estonian notice 105
- Finnish notice 105
- Greek notice 106
- Hungarian notice 106
- Italian n 106
- Latvian notice 106
- Lithuanian notice 107
- Polish notice 107
- Portugue 107
- Slovakian notice 107
- Germany noise declaration 108
- Japanese notice 109
- Taiwanese notice 109
- Japanese 109
- Country-specificcertifications 109
- Physical specifications 110
- Power speci 111
- fications 111
- Fibre Channel sw 113
- Controller specifications 113
- Rack specifications 114
- Environmental specifications 116
- Power specifications 116
- Nominal inp ut voltage 117
- Specifications 117
- The power 117
- Condition report format 119
- Correcting err ors 120
- Power supply conditions 122
- 0.2.en.02 123
- Blower conditions 124
- Temperature conditions 125
- 0.4.en.01 N 126
- 0.4.en.03 NON 127
- EMU conditions 128
- Transceiver conditions 132
- 0.F.en.05 C 133
- Backplane conditions 135
- I/O Module conditions 135
- Host conditions 137
- C Controller fault management 139
- GUI event display 140
- Fault management displays 140
- Information type 142
- Description 142
- Glossary 143
Produits connexes et manuels pour Logiciel de gestion du système HP EVA3000
(105 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels