Hp ProLiant MicroServer Gen8 Manuel d'utilisateur Page 30
- Page / 95
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Setup 30
for ProLiant Gen8 Servers and HP BladeSystem c-Class Enclosures on the HP website
(http://www.hp.com/go/insightremotesupport/docs).
Configure the drive
If you intend to use an HP Smart Array controller card option ("Installing a storage controller" on page 43),
record the model name for this procedure.
For more information about the storage controller and its features, select the relevant controller user
documentation on the HP website (http://www.hp.com/go/smartstorage/docs).
To configure arrays, see the HP Smart Storage Administrator User Guide on the HP website
(http://www.hp.com/go/smartstorage/docs).
To create a drive array:
1. On the Intelligent Provisioning main screen, click Perform Maintenance.
2. On the Maintenance screen, click HP Smart Storage Administrator (HP SSA).
The system launches the HP SSA GUI.
3. On the left-hand side of the screen, select the preferred HP Smart Array Controller device, and then click
Configure under the available options.
The Configure panel is displayed.
4. Click Create Array.
5. Select the array settings for the selected device.
6. Use the Next and Back buttons to navigate multiple screens of options.
7. Click Save or OK.
8. Click Exit HP SSA.
9. Click PREVIOUS.
Install the operating system
1. If you are installing the OS from a disc or an external USB drive, do one of the following:
o Load the OS image disc to the server optical drive. If an optical drive is not installed, connect a USB
optical drive to the server USB 2.0 connector.
o Connect the USB storage drive containing the OS image to the server USB 2.0 connector.
2. On the Intelligent Provisioning main screen, select Configure and Install.
3. The system detects the default hardware settings. Retain these settings or customize them according to
your requirements.
4. Follow the onscreen prompts to install the OS.
Complete the system setup
Check the status of the server LEDs to ensure that the server is operating normally:
• System power LED —Solid green
• NIC status LED —Solid green
• Drive status LED —Solid green
- HP ProLiant MicroServer Gen8 1
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs and buttons 7
- Rear panel components 8
- Rear panel LEDs and buttons 9
- System board components 9
- Item Description 10
- DIMM slot locations 11
- System maintenance switch 11
- Drive numbering 12
- FBWC module LED definitions 13
- Fan location 14
- T-10/T-15 Torx screwdriver 14
- Operations 15
- Open the front bezel 16
- Remove the front bezel 17
- Install the front bezel 18
- Remove the chassis cover 19
- Install the chassis cover 19
- Operations 21 21
- Operations 22 22
- Optimum environment 23
- Temperature requirements 24
- Power requirements 24
- Server warnings and cautions 25
- Installing hardware options 25
- Setup 26 26
- • Dedicated iLO connector 27
- Configure the drive 30
- Install the operating system 30
- Complete the system setup 30
- Registering the server 31
- Setup 32 32
- Complete the switch setup 37
- Introduction 38
- Bezel faceplate 38
- Drive options 40
- Controller options 42
- Optical drive option 46
- Memory options 48
- HP SmartMemory 49
- DIMM identification 49
- ECC memory 50
- Installing a DIMM 51
- Expansion board options 52
- Cabling 57
- Capacitor pack cabling 58
- Optical drive cabling 59
- Front I/O assembly cabling 59
- System fan cabling 60
- Power supply cabling 61
- Server mode 62
- Product QuickSpecs 62
- HP iLO Management 62
- Active Health System 63
- Intelligent Provisioning 64
- HP Insight Diagnostics 65
- Erase Utility 65
- HP Service Pack for ProLiant 67
- HP ROM-Based Setup Utility 67
- Boot options 68
- Utilities and features 69
- Keeping the system current 70
- Software and firmware 71
- Version control 71
- ProLiant servers 71
- Troubleshooting 73
- System battery replacement 74
- Regulatory information 75
- Warranty information 76
- Electrostatic discharge 77
- Specifications 78
- Specification Value 79
- Support and other resources 80
- Customer Self Repair 82
- Reparo feito pelo cliente 84
- Acronyms and abbreviations 88
- Virtual Connect 91
- Version Control Agent 91
- Documentation feedback 92
- Index 93 93
- Index 94 94
- Index 95 95
Produits connexes et manuels pour Matériel informatique Hp ProLiant MicroServer Gen8
(147 pages)
(187 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels