HP Series 7 Guide de l'utilisateur Page 134
- Page / 186
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
134 www.xilinx.com 7 Series FPGAs SelectIO Resources User Guide
UG471 (v1.5) May 15, 2015
Chapter 2: SelectIO Logic Resources
ODELAY Ports
Data Input from the FPGA OLOGICE2/OSERDESE2 - ODATAIN
The ODATAIN input is driven by OLOGICE2/OSERDESE2. The ODATAIN drives the
DATAOUT port which is connected to an IOB with a delay set by the ODELAY_VALUE.
Clock Input from Clock Buffer - CLKIN
The CLKIN input is driven from clock buffers (BUFIO, BUFG, or BUFR). The clock is
driven back into the FPGA logic through the DATAOUT port with a delay set by the
ODELAY_VALUE.
Data Output - DATAOUT
Delayed data from one of the two data input ports. DATAOUT connects to the IOB.
Clock Input - C
All control inputs to ODELAYE2 primitive (LD, CE, and INC) are synchronous to the clock
input (C). A clock must be connected to this port when ODELAY is configured in
VARIABLE, VAR_LOAD, or VAR_LOAD_PIPE mode. C can be locally inverted, and must
be supplied by a global or regional clock buffer. This clock must be connected to the same
clock as used in the SelectIO logic resources. For example, when using the OSERDESE2,
C is connected to the same clock as CLKDIV. If the IDELAYE2 primitive is used in the same
I/O bank as the ODELAYE2 primitive, C must use the same clock net for both primitives.
Module Load - LD
When in VARIABLE mode, the ODELAY load port, LD, loads the delay primitive to a
value set by the ODELAY_VALUE attribute. If these attributes are not specified, a value of
zero is assumed. The LD signal is an active-High signal and is synchronous to the input
clock signal (C).
When in VAR_LOAD mode, the ODELAY load port, LD, loads the delay primitive to a
value set by the CNTVALUEIN. The value present at CNTVALUEIN[4:0] will be the new
tap value. As a result of this functionality the ODELAY_VALUE attribute is ignored.
When in VAR_LOAD_PIPE mode, the IDELAY load port, LD, loads the value currently in
the pipeline register. The value present in the pipeline register will be the new tap value.
Pipeline Register Load - LDPIPEEN
When High, this input loads the pipeline register with the value currently on the
CNTVALUEIN pins.
ODATAIN Input 1 Data input for ODELAY from the OLOGICE2/OSERDESE2.
LDPIPEEN Input 1
Enables the pipeline register to load data from CNTVALUEIN.
DATAOUT Output 1 Delayed data from one of two data input ports (ODATAIN and CLKIN).
CNTVALUEOUT Output 5 Current delay value going to FPGA logic for monitoring tap value.
Table 2-13: ODELAYE2 Primitive Ports (Cont’d)
Port
Name
Direction Width Function
- 7 Series FPGAs 1
- SelectIO Resources 1
- Revision History 2
- Table of Contents 5
- UG471 (v1.5) May 15, 2015 10
- About This Guide 11
- Preface: About This Guide 12
- New Features 14
- 7 Series FPGA I/O Bank Rules 17
- Introduction 19
- Xilinx DCI 20
- DCIRESET Primitive 22
- DCI Cascading 22
- DCI and 3-state DCI (T_DCI) 28
- DCI Usage Examples 31
- IBUF and IBUFG 35
- IBUF_IBUFDISABLE 35
- IBUF_INTERMDISABLE 36
- IBUFDS and IBUFGDS 36
- IBUFDS_DIFF_OUT_IBUFDISABLE 37
- IBUFDS_IBUFDISABLE 37
- IBUFDS_INTERMDISABLE 38
- IBUFDS_DIFF_OUT_INTERMDISABLE 38
- IOBUF_DCIEN 39
- IOBUF_INTERMDISABLE 40
- IOBUFDS_DCIEN 41
- IOBUFDS_DIFF_OUT 42
- IOBUFDS_DIFF_OUT_DCIEN 43
- IOBUFDS_INTERMDISABLE 44
- DCI_CASCADE Constraint 46
- Location Constraints 47
- IOSTANDARD Attribute 47
- IBUF_LOW_PWR Attribute 47
- Output Slew Rate Attributes 48
- VCCAUX_IO Constraint 50
- LVTTL (Low Voltage TTL) 51
- LVCMOS (Low Voltage CMOS) 54
- LVDCI _ DV2 57
- HSLVDCI (High-Speed LVDCI) 59
- HSTL_ I and HSTL_ I_18 60
- HSTL_I_12 60
- HSTL_ II and HSTL_ II_18 60
- N/A Available 62
- External Termination 63
- Differential HSTL Class I 64
- HSTL Class II 66
- Differential HSTL Class II 68
- Not 3-stated 72
- (T pin logic Low) 72
- 3-stated 72
- (T pin logic High) 72
- SSTL18_I, DIFF_SSTL18_I 76
- DIFF_SSTL135 76
- User Guide for details 77
- HSUL_12 and DIFF_HSUL_12 84
- Example Board Topology 85
- Differential HSUL_12 86
- MOBILE_DDR (Low Power DDR) 88
- Transmitter Termination 91
- Receiver Termination 91
- Differential Clock 93
- Input to the FPGA 93
- BLVDS (Bus LVDS) 96
- Table 1-55: V 99
- Chapter 1: SelectIO Resources 102
- SelectIO Logic Resources 105
- ILOGIC Resources 106
- ZHOLD_DELAY 108
- OPPOSITE_EDGE Mode 109
- SAME_EDGE Mode 110
- SAME_EDGE_PIPELINED Mode 110
- Input DDR Resources (IDDR) 111
- ILOGIC Timing Models 112
- Clock Event 4 113
- Clock Event 1 113
- Clock Event 9 114
- IDELAYE2 Primitive 115
- IDELAY Ports 116
- IDELAYRESOLUTION 117
- IDELAY Attributes 118
- IDELAY Modes 119
- IDELAY Timing 120
- Clock Event 2 121
- Clock Event 3 121
- Clock Event 0 122
- IDELAYCTRL 123
- IDELAYCTRL Timing 124
- IDELAYCTRL Locations 124
- OLOGIC Resources 125
- Output DDR Overview (ODDR) 126
- Clock Forwarding 127
- Output DDR Primitive (ODDR) 128
- OLOGIC Timing Models 128
- Timing Characteristics 129
- ODELAYE2 Primitive 133
- ODELAY Ports 134
- ODELAY Attributes 136
- ODELAY Modes 137
- ODELAY Timing 138
- Chapter 3 141
- ISERDESE2 143
- Primitive 143
- Registered Outputs – Q1 to Q8 144
- Combinatorial Output – O 145
- Bitslip Operation - BITSLIP 145
- High-Speed Clock Input - CLK 146
- High-Speed Clock Input - CLKB 146
- Divided Clock Input - CLKDIV 146
- Oversampling Mode - OCLK 147
- Reset Input - RST 147
- ISERDESE2 Attributes 148
- DATA_RATE Attribute 149
- DATA_WIDTH Attribute 149
- INTERFACE_TYPE Attribute 149
- ISERDESE2 Clocking Methods 150
- MEMORY Interface Type 151
- MEMORY_QDR Interface Type 151
- OVERSAMPLE Interface Type 151
- ISERDESE2 Width Expansion 153
- OSERDESE2 154
- BITSLIP Submodule 156
- After Clock Event 3 158
- OSERDESE2 Primitive 160
- Data Path Output - OQ 161
- DATA_RATE_OQ Attribute 163
- DATA_RATE_TQ Attribute 163
- SERDES_MODE Attribute 164
- TRISTATE_WIDTH Attribute 164
- OSERDESE2 Width Expansion 165
- Output Feedback 166
- OSERDESE2 Latencies 166
- IO_FIFO Overview 171
- FIFO Core 172
- 7 Entries Deep 172
- Register Register 172
- IN_FIFO Primitive 173
- Table 3-15: IN_FIFO Ports 174
- OUT_FIFO 175
- OUT_FIFO Primitive 176
- Table 3-18: OUT_FIFO Ports 177
- Resetting the IO_FIFO 178
- EMPTY and FULL Flags 178
- Termination Options for 181
- SSO Noise Analysis 181
- TMDS_33 Far 3.3V 50Ω 183
- IO Standard 183
- Default Termination 183
Produits connexes et manuels pour PC/postes de travail HP Series 7
(44 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.555 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels