HP E5000 Guide de l'utilisateur Page 97
- Page / 207
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5. Verify that the replacement component is working properly by checking the associated LED
status.
6. Confirm the system has resumed normal operations.
Removing and replacing the Enclosure Manager Unit
IMPORTANT: Be sure to unpack the replacement part before you remove the existing component.
This section describes how to remove and replace the Enclosure Manager Unit in the messaging
system.
Removing the Enclosure Manager Unit module
To remove the Enclosure Manager Unit module:
1. Use System Manager to identify the failed component.
2. Verify the failed component by checking for a blinking amber LED on the failed component.
3. Unplug any cables from the Enclosure Manager Unit module.
4. Press the Enclosure Manager Unit module release lever to the right (1), and then remove the
Enclosure Manager Unit module (2).
Replacing the Enclosure Manager Unit module
To replace the Enclosure Manager Unit module:
1. Insert the replacement Enclosure Manager Unit module and ensure the release lever locks in
place for module installation.
Removing and replacing the Enclosure Manager Unit 97
- Exchange Administrator Guide 1
- DescriptionSoftware 2
- DateEdition 2
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Messaging system features 7
- E5000 EMU network connections 9
- Check the kit contents 14
- 1. Messaging system enclosure 15
- Install E5000 expansion nodes 16
- Power on the messaging system 17
- 2. Monitor 22
- 3. Keyboard 22
- 4. Mouse 22
- Configuring server software 24
- Click Next 25
- Next steps 35
- Using notification alerts 37
- System Summary 44
- Hardware Status 44
- Exchange Status 45
- Firmware 46
- HP System Management Homepage 48
- Overall System Health Status 50
- Component Status summary 50
- Component LEDs 51
- Figure 13 Hard drive LEDs 54
- Table 7 (continued) 56
- Figure 21 Fan LEDs 58
- EMU CLI SHOW commands 59
- HP Support websites 60
- Customer self repair 69
- Replaceable parts 70
- Replaceable parts 71 71
- Verifying component failure 73
- Verifying proper operation 74
- Wait times for hard disks 74
- Removing the midplane board 77
- 18. Extend the server blades 80
- Replacing the midplane board 81
- Removing the SAS cable 82
- Replacing the SAS cable 83
- Removing the SAS I/O module 83
- Replacing the SAS I/O module 83
- Removing the drive fan module 85
- Removing the power supply 90
- Replacing the power supply 90
- Removing the Mezzanine NIC 92
- Replacing the Mezzanine NIC 94
- Removing the PCIe module 95
- Replacing the PCIe module 96
- Removing the front bezel 106
- Replacing the front bezel 107
- Removing the drive drawer 118
- 16. Extend the drive drawer 120
- Replacing the drive drawer 121
- Removing the enclosure rails 132
- Replacing the enclosure rails 134
- Removing the server blade 137
- Replacing the server blade 138
- Removing the controller card 139
- Replacing the controller card 141
- Replacing the cache module 143
- Removing the capacitor pack 144
- Replacing the capacitor pack 145
- 8 Messaging System recovery 147
- 148 Messaging System recovery 148
- 9 Support and other resources 150
- Typographic conventions 151
- Rack stability 152
- A EMU reference 153
- Authentication 154
- ENABLE USER 155
- REMOVE USER 155
- SET PASSWORD 155
- SET USER PASSWORD 155
- SHOW USER 156
- SHOW SSHFINGERPRINT 156
- SHOW SSHKEY 156
- Time functions 157
- SET TIMEZONE 158
- ENABLE NTP 158
- DISABLE NTP 158
- CLEAR NTP 159
- SET NTP POLL 159
- SET NTP PRIMARY 159
- SET NTP SECONDARY 159
- Inventory and status 160
- SHOW DISPLAY EVENTS 161
- SHOW ENCLOSURE FAN 162
- SHOW ENCLOSURE INFO 162
- SHOW ENCLOSURE POWERSUPPLY 163
- SHOW ENCLOSURE STATUS 164
- SHOW ENCLOSURE TEMP 164
- SHOW FRU 165
- 166 EMU reference 166
- SHOW IOMODULES 167
- SHOW RACK 168
- SHOW SERVER TEMP 168
- Internet control 169
- SET EBIPA 170
- SET EM GATEWAY 170
- Server management 171
- POWEROFF SERVER 172
- POWERON SERVER 172
- REBOOT SERVER 172
- RESET SERVER 172
- SET SERVER UID 173
- SET SERVER BOOT 173
- SHOW SERVER NAMES 173
- SHOW SERVER BOOT 174
- SHOW SERVER INFO 174
- Restrictions 175
- SHOW SERVER LIST 176
- SHOW SERVER STATUS 176
- Enclosure control 177
- UPLOAD CONFIG 178
- SET EM NAME 178
- SET ENCLOSURE ASSET 178
- SET ENCLOSURE ID 178
- SET ENCLOSURE NAME 179
- SET ENCLOSURE UID 179
- SET FACTORY 179
- Forensic 180
- SHOW SYSLOG SERVER 181
- SHOW SYSLOG EM 181
- SHOW SYSLOG SETTINGS 181
- TEST SYSLOG 181
- SET REMOTE SYSLOG SERVER 182
- SET REMOTE SYSLOG PORT 182
- ENABLE SYSLOG REMOTE 182
- DISABLE SYSLOG REMOTE 182
- CLEAR SCREEN 183
- CONNECT SERVER 183
- SET SCRIPT 184
- SHOW SESSION TIMEOUT 184
- SET SESSION TIMEOUT 184
- Manual button functions 185
- Reboot EM (bE) 186
- Restore Factory Defaults (Fd) 186
- Recover Lost Password (Fp) 186
- Set DHCP IP Address (dH) 186
- Exit Button Menu 187
- FCC rating label 188
- European Union notice 189
- Japanese notices 190
- Korean notices 190
- Taiwanese notices 191
- Laser compliance notices 192
- German laser notice 193
- Italian laser notice 193
- Japanese laser notice 193
- Recycling notices 194
- Bulgarian recycling notice 195
- Czech recycling notice 195
- Danish recycling notice 195
- Dutch recycling notice 195
- Estonian recycling notice 196
- Finnish recycling notice 196
- French recycling notice 196
- German recycling notice 196
- Greek recycling notice 197
- Hungarian recycling notice 197
- Italian recycling notice 197
- Latvian recycling notice 197
- Lithuanian recycling notice 198
- Polish recycling notice 198
- Portuguese recycling notice 198
- Romanian recycling notice 198
- Slovak recycling notice 199
- Spanish recycling notice 199
- Swedish recycling notice 199
- Turkish recycling notice 199
- Battery replacement notices 200
- German battery notice 201
- Italian battery notice 201
- Japanese battery notice 202
- Spanish battery notice 202
- Glossary 203
- 204 Index 204
- 206 Index 206
Produits connexes et manuels pour Serveurs HP E5000
Serveurs HP DL380 Guide de l'utilisateur
(20 pages)
(20 pages)
Serveurs HP SCSI Manuel d'utilisateur
(34 pages)
(34 pages)
Serveurs HP RP7405/7410 Manuel d'utilisateur
(146 pages)
(146 pages)
Serveurs HP 400R Manuel d'utilisateur
(21 pages)
(21 pages)
(58 pages)
Serveurs HP i2000 Manuel d'utilisateur
(49 pages)
(49 pages)
Serveurs HP C3000 Manuel d'utilisateur
(37 pages)
(37 pages)
Serveurs HP A5150A Manuel d'utilisateur
(76 pages)
(76 pages)
Serveurs HP SP400 Guide de l'utilisateur
(66 pages)
(66 pages)
Serveurs HP B132L+ Manuel d'utilisateur
(256 pages)
(256 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels