HP Series 7 Guide de l'utilisateur Page 24
- Page / 186
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
24 www.xilinx.com 7 Series FPGAs SelectIO Resources User Guide
UG471 (v1.5) May 15, 2015
Chapter 1: SelectIO Resources
The guidelines when using DCI cascading are as follows:
• DCI cascading is only available through a column of HP I/O banks
• The master and slave SelectIO banks must all reside on the same HP I/O column on
the device and can span the entire column unless there is an interposer boundary.
• DCI cascading cannot pass through the interposer boundaries of the larger
Virtex-7 devices with stacked silicon interconnect (SSI) technology. This includes the
XC7V2000T and XC7VX1140T devices. For these devices, the I/O banks that are
separated by these interposer boundaries are shown in the figures of the “Die Level
Bank Numbering Overview” section of UG475
: 7 Series FPGAs Packaging and Pinout
Specifications.
• Master and slave I/O banks must have the same V
CCO
and V
REF
(if applicable)
voltage.
• I/O banks in the same HP I/O column that are not using DCI (pass-through banks)
do not have to comply with the V
CCO
and V
REF
voltage rules for combining DCI
settings.
• DCI I/O banking compatibility rules must be satisfied across all master and slave
banks (for example, only one DCI I/O standard using single termination type is
allowed across all master and slave banks).
• To locate I/O banks that reside in the same I/O column, refer to the figures of the “Die
Level Bank Numbering Overview” section of UG475
: 7 Series FPGAs Packaging and
Pinout Specifications.
• For specific information on implementing DC cascading in a design, see
DCI_CASCADE Constraint, page 46.
• Xilinx recommends that unused banks be powered up because leaving the V
CCO
pins
of unused I/O banks floating reduces the level of ESD protection on these pins and
the I/O pins in the bank. If the bank is unpowered, DCI can still be cascaded through
the unpowered bank.
- 7 Series FPGAs 1
- SelectIO Resources 1
- Revision History 2
- Table of Contents 5
- UG471 (v1.5) May 15, 2015 10
- About This Guide 11
- Preface: About This Guide 12
- New Features 14
- 7 Series FPGA I/O Bank Rules 17
- Introduction 19
- Xilinx DCI 20
- DCIRESET Primitive 22
- DCI Cascading 22
- DCI and 3-state DCI (T_DCI) 28
- DCI Usage Examples 31
- IBUF and IBUFG 35
- IBUF_IBUFDISABLE 35
- IBUF_INTERMDISABLE 36
- IBUFDS and IBUFGDS 36
- IBUFDS_DIFF_OUT_IBUFDISABLE 37
- IBUFDS_IBUFDISABLE 37
- IBUFDS_INTERMDISABLE 38
- IBUFDS_DIFF_OUT_INTERMDISABLE 38
- IOBUF_DCIEN 39
- IOBUF_INTERMDISABLE 40
- IOBUFDS_DCIEN 41
- IOBUFDS_DIFF_OUT 42
- IOBUFDS_DIFF_OUT_DCIEN 43
- IOBUFDS_INTERMDISABLE 44
- DCI_CASCADE Constraint 46
- Location Constraints 47
- IOSTANDARD Attribute 47
- IBUF_LOW_PWR Attribute 47
- Output Slew Rate Attributes 48
- VCCAUX_IO Constraint 50
- LVTTL (Low Voltage TTL) 51
- LVCMOS (Low Voltage CMOS) 54
- LVDCI _ DV2 57
- HSLVDCI (High-Speed LVDCI) 59
- HSTL_ I and HSTL_ I_18 60
- HSTL_I_12 60
- HSTL_ II and HSTL_ II_18 60
- N/A Available 62
- External Termination 63
- Differential HSTL Class I 64
- HSTL Class II 66
- Differential HSTL Class II 68
- Not 3-stated 72
- (T pin logic Low) 72
- 3-stated 72
- (T pin logic High) 72
- SSTL18_I, DIFF_SSTL18_I 76
- DIFF_SSTL135 76
- User Guide for details 77
- HSUL_12 and DIFF_HSUL_12 84
- Example Board Topology 85
- Differential HSUL_12 86
- MOBILE_DDR (Low Power DDR) 88
- Transmitter Termination 91
- Receiver Termination 91
- Differential Clock 93
- Input to the FPGA 93
- BLVDS (Bus LVDS) 96
- Table 1-55: V 99
- Chapter 1: SelectIO Resources 102
- SelectIO Logic Resources 105
- ILOGIC Resources 106
- ZHOLD_DELAY 108
- OPPOSITE_EDGE Mode 109
- SAME_EDGE Mode 110
- SAME_EDGE_PIPELINED Mode 110
- Input DDR Resources (IDDR) 111
- ILOGIC Timing Models 112
- Clock Event 4 113
- Clock Event 1 113
- Clock Event 9 114
- IDELAYE2 Primitive 115
- IDELAY Ports 116
- IDELAYRESOLUTION 117
- IDELAY Attributes 118
- IDELAY Modes 119
- IDELAY Timing 120
- Clock Event 2 121
- Clock Event 3 121
- Clock Event 0 122
- IDELAYCTRL 123
- IDELAYCTRL Timing 124
- IDELAYCTRL Locations 124
- OLOGIC Resources 125
- Output DDR Overview (ODDR) 126
- Clock Forwarding 127
- Output DDR Primitive (ODDR) 128
- OLOGIC Timing Models 128
- Timing Characteristics 129
- ODELAYE2 Primitive 133
- ODELAY Ports 134
- ODELAY Attributes 136
- ODELAY Modes 137
- ODELAY Timing 138
- Chapter 3 141
- ISERDESE2 143
- Primitive 143
- Registered Outputs – Q1 to Q8 144
- Combinatorial Output – O 145
- Bitslip Operation - BITSLIP 145
- High-Speed Clock Input - CLK 146
- High-Speed Clock Input - CLKB 146
- Divided Clock Input - CLKDIV 146
- Oversampling Mode - OCLK 147
- Reset Input - RST 147
- ISERDESE2 Attributes 148
- DATA_RATE Attribute 149
- DATA_WIDTH Attribute 149
- INTERFACE_TYPE Attribute 149
- ISERDESE2 Clocking Methods 150
- MEMORY Interface Type 151
- MEMORY_QDR Interface Type 151
- OVERSAMPLE Interface Type 151
- ISERDESE2 Width Expansion 153
- OSERDESE2 154
- BITSLIP Submodule 156
- After Clock Event 3 158
- OSERDESE2 Primitive 160
- Data Path Output - OQ 161
- DATA_RATE_OQ Attribute 163
- DATA_RATE_TQ Attribute 163
- SERDES_MODE Attribute 164
- TRISTATE_WIDTH Attribute 164
- OSERDESE2 Width Expansion 165
- Output Feedback 166
- OSERDESE2 Latencies 166
- IO_FIFO Overview 171
- FIFO Core 172
- 7 Entries Deep 172
- Register Register 172
- IN_FIFO Primitive 173
- Table 3-15: IN_FIFO Ports 174
- OUT_FIFO 175
- OUT_FIFO Primitive 176
- Table 3-18: OUT_FIFO Ports 177
- Resetting the IO_FIFO 178
- EMPTY and FULL Flags 178
- Termination Options for 181
- SSO Noise Analysis 181
- TMDS_33 Far 3.3V 50Ω 183
- IO Standard 183
- Default Termination 183
Produits connexes et manuels pour PC/postes de travail HP Series 7
(44 pages)© 2020, manymanuals.fr. Tous droits réservés | 8.728 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels